User manual MITSUBISHI XD211U

[. . . ] DATA PROJECTOR MODEL XD211U User Manual XD211U This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: CAUTION: NOTE: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. [. . . ] (Wait about 10 minutes before turning the projector back on. ) · Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without closing the menu, the setting data of the menu may not be saved. · · Important: · AUTO POSITION button When the image isn't projected in the right position with COMPUTER selected as the input source, follow the procedure below. Project a bright image such as the "Recycle Bin" window on the full screen. If the screen saver is running, turn it off. · If the image is still not in the right position, adjust the image position using the Computer Image menu. See page 15. When connecting to a laptop computer: · VOLUME button Press the KEYSTONE/VOLUME button to select Keystone or Volume, and press the or button to change the volume from the speaker. The volume control bar will appear on the screen. · · The volume control bar will disappear according to OSD Timeout after the VOLUME button is released. The VOLUME buttons don't function while the menu selection bar or the menu is being displayed. EN-14 Menu operation * Menus are not displayed when no signal is supplied to the projector. Picture Brightness*1 Contrast*2 Color Setting Keystone Aspect Image White Intensity*3 *4 Gamma*3 *4 Tracking*5 *7 Fine sync*5 H Position*5 *7 V Position*5 *7 Video Image*8 Color*1 *2 Sharpness Tint*9 Set up*10 Sound Volume Menu Position Mounting Logo Signal Type*6 Lamp Time Lamp Time Reset Auto Power On Auto Power Off Auto Source Lamp Mode OSD Timeout Language Yes, No Standard, Low 5, 15, 30, 45, 60 Sec Yes, No Yes, No On, Off RGB, YCbCr/YPbPr -20-+20 4:3, 16:9 PC, Movie, Standard, User 0 - 10 0-6 -50 - +50 0 - 31 -10 - +10 -10 - +10 0 - 100 0 - 100 Red, Green, Blue Computer Image*6 0 - 100 0 - 31 0 - 100 0%, 7. 5% 0 - 31 Setting Factory Default Yes, No *1 Default setting varies depending on input signals. *2 Available only when the input signal is PC or Video or S-Video 4/5 line component signal. *3 Setting value varies depending on the setting of Image. *4 Only adjustable when Image setting is User. *5 Adjustable range and default setting vary depending on signal type. *6 Not available when the input signal is Video or S-Video. *7 Only available when the input signal is PC. *8 Not available when the input signal is PC. *9 Only available when the input signal is Video / S-Video 480i 480p. *10 Only available when input signal is NTSC. Important: · When the menu is turned on and the signal is lost or not input, the system will not search for the signal even if the signal is input again. · The setting will be saved even if the menu is closed. · The setting will not be saved when the menu is closed in a no signal state. EN-15 ENGLISH Menu operation (continued) Basic operation 3. Several settings can be adjusted using the menu. [. . . ] Images with SYNC on G (Green) signal may be tinged with green. If the resolution and frequency of your computer aren't shown on the table, find the compatible resolution and frequency by changing the resolution of your computer. When connecting a HDTV decoder having RGB output terminals, set Signal Type to RGB in the Setting menu. Video signal with 4 line (R, G, B, CS) and 5 line (R, G, B, H, V) is not supported. [. . . ]