User manual MITSUBISHI XD435UG CONTROL PROJECTOR BY USING A PERSONAL COMPUTER

[. . . ] (3) The personal computer checks the command and confirms if the sent command has been executed or not. (4) This projector sends various codes other than the return code. When having a control sequence by RS-232C, reject other codes from the personal computer. [. . . ] This command will not be executed in Stand-by mode or the MUTE is executed. This command will not be executed in Stand-by mode or the MUTE is executed. This command will not be executed in Stand-by mode or the MUTE is executed. This command will not be executed in Stand-by mode or the MUTE is executed. 72h 72h 76h 76h 73h 31h 32h 31h 32h 31h * XD435U only [Example] When setting the input signal to COMPUTER 1 (Figures and symbols enclosed in quotation marks are ASCII codes. ): Status code from the projector Command for setting the input 30 30 5F 72 31 0D '0' '0' '_' 'r' '1' ' ' signal to COMPUTER 1 Command receipt confirmation (Command echo back) Description Sending commands from the PC, etc. 30 30 5F 72 31 0D '0' '0' '_' 'r' '1' ' ' 5) Volume commands (Not executable in stand-by mode. Possible only to read during muting. ) The volume commands are used for the volume setting of this projector with the value. ITEM VOLUME ASCII VL HEX 56h 4Ch VALUE 00 - 21 How to set the grade Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code. ASCII '0' '1' '2' '3' '4' '5' '6' '7' '8' '9' HEX 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h [Example] When setting the volume to 15 (Figures and symbols enclosed in quotation marks are ASCII codes. ): Status code from the projector Description Command for setting the volume 30 30 56 4C 31 35 0D '0' '0' 'V' 'L' '1' '5' ' ' Command receipt confirmation (Command echo back) Sending commands from the PC, etc. 30 30 56 4C 31 35 0D '0' '0' 'V' 'L' '1' '5' ' ' 2 6) Keystone commands (Not executable in stand-by mode. Possible only to read during muting. ) The keystone commands are used for the keystone setting of this projector with the value. The value will vary depending on the installation conditions, etc. ) ITEM KEYSTONE(vertical) ASCII KS HEX 4Bh 53h VALUE ±20 How to set the grade Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code. ASCII HEX '+' 2Bh '­' 2Dh '0' 30h '1' 31h '2' 32h '3' 33h '4' 34h '5' 35h '6' 36h '7' 37h '8' 38h '9' 39h 7) Mute commands (Not executable in stand-by mode. When the mute commands are sent while the splash screen is being displayed, the splash screen is not muted but only canceled. ) The mute commands are used for the mute setting of this projector with the 0(30h) and 1(31h). ITEM MUTE ASCII MUTE HEX 4Dh 55h 54h 45h VALUE 0 (OFF), 1 (ON) 8) Remote commands (Not executable in stand-by mode. When the remote commands are sent while the splash screen is being displayed, the splash screen is only canceled. ) Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes. Button's name on remote + VOLUME ­ VOLUME KEYSTONE MUTE t s MENU ENTER AUTO POSITION STILL 16:9 USB DEVICE UNPLUG* ASCII r06 r07 r43 ra6 r53 r2b r4f r59 r54 r10 r09 ra4 re2 rb5 HEX 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 30h 30h 34h 61h 35h 32h 34h 35h 35h 31h 30h 61h 65h 62h 36h 37h 33h 36h 33h 62h 66h 39h 34h 30h 39h 34h 32h 35h * XD435U only [Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII codes. ): Status code from the projector Command operating the same 30 30 72 35 34 0D '0' '0' 'r' '5' '4' ' ' as the MENU button Command receipt confirmation (Command echo back) Description Sending commands from the PC, etc. 30 30 72 35 34 0D '0' '0' 'r' '5' '4' ' ' 9) Password lock commands The password lock commands control the password lock. The password lock enabling or disabling command is sent with a 4-digit figure (password) added to the end of the data code. [. . . ] TRACKING COMPUTER INPUT SET UP HOLD HOLD BEGIN HOLD END CLAMP POSITION CLAMP WIDTH UNPLUG DEVICE* AUTO START* REPEAT SETTING* INTERVAL TIME* TRANSITION EFFECT* ASCII RSTALL HP VP FN TRK CIN STU HLD HLB HLE CLP CLW UUD UAS URS UIT UTE HEX 52h 53h 54h 48h 50h 56h 50h 46h 4Eh 54h 52h 43h 49h 53h 54h 48h 4Ch 48h 4Ch 48h 4Ch 43h 4Ch 43h 4Ch 55h 55h 55h 41h 55h 52h 55h 49h 55h 49h 41h 4Bh 4Eh 55h 44h 42h 45h 50h 57h 44h 53h 53h 54h 45h THUMBNAIL DISPLAY* UTD 55h 49h 44h VALUE 4Ch 4Ch + (increment), - (decrement) + (increment), - (decrement) 00 - 31 + (increment), - (decrement) 0 (RGB), 1 (YCBCR/YPBPR), 2(AUTO) 1 (OFF), 2 (3. 75%), 3 (7. 5%) 0 (OFF), 1 (ON) 00 - 99 00 - 99 00 - 63 01 - 63 0(OFF), 1(ON) 0(OFF), 1(ON) 0(5 sec. ), 1(10 sec. ), 2(30 sec. ), 3(1 min. ), 4(3 min. ) 00=NONE, 01=SLIDE IN , 02=SLIDE IN 03=WIPE , 04=WIPE , 05=WIPE , 06=WIPE 07=SPLIT WIPE IN , 08=SPLIT WIPE OUT , 09=SPLIT WIPE IN , 10=SPLIT WIPE OUT 11=BLIND , 12=BLIND , 13=BOX WIPE IN 14=BOX WIPE OUT, 15=DISSOLVE1, 16=DISSOLVE2 0(OFF), 1(ON) * XD435U only · Some commands are not executed depending on the input signal. The operational restrictions same as those on the menu setting are applied. Refer to "Menu operation" in the User Manual for more details. [. . . ]