User manual MITSUBISHI XD490

[. . . ] DLPTM PROJECTOR MODEL XD490U XD460U User Manual This User Manual is important to you. Please read it before using your projector. XD490 XD460 ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable and RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class B device. [. . . ] (See page 26. ) Use to adjust the color thickness of the projected image. (See page 25. ) Use to adjust the color tint of the projected image. (See page 25. ) · When the TV50 (PAL, SECAM) signal is input, TINT can't be adjusted. Use to adjust the sharpness of the projected image. (See page 25. ) FUNCTION Select any option depending on the color of the wall on which images are projected. When selecting any option other than BLACK BOARD, you can make fine adjustment of color tone (1 to 5). (See page 11. ) Use to adjust the screen size and position. (See page 12. ) Select this option when you want to view images in a well-lit room. Select to moderate the intensity of the lamp. The operating sound is reduced and the lamp lifetime becomes longer. · When the lamp mode is switched, the projected image may flicker. · Frequent switching of the lamp mode may damage the lamp. When ON is chosen, the lamp is automatically lit when the power cord is plugged in the wall outlet. Choose ON when using the projector mounted on the ceiling. · The projector is in the stand-by mode when the lamp is off. Use the remote control to turn on the lamp. Use to set the time elapsed before the projector enters the stand-by mode when there is no signal input from the source. Choose ON to display the splash screen when the power is turned on. Use to change the color of the screen that appears when no signal is supplied. Select when viewing images from the front with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the ceiling. Select when viewing images from the front with the projector installed on the ceiling. 2. [. . . ] · Video signals having resolution exceeding the maximum resolution supported by this projector are reduced to the maximum resolution size of the projector even in the REAL mode. · This projector doesn't support 480i, 576i, and 480p signals from video devices having 5 lines (R, G, B, H, V). EN-38 SERIAL (8-pin) 12 10 5 1 Pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC 5V GND GND DDC Data HD/CS VD DDC Clock 16 9 6 15 11 3 5 1 2 3 4 5 6 8 1 PIN No. 1 2 3 4 5 6 7 8 9 10 11 12 SPEC DATA 2DATA 2+ DATA 2 Shield DDC Clock DDC Data DATA 1DATA 1+ DATA 1 Shield - PIN No. [. . . ]