User manual MITSUBISHI XL7000U

[. . . ] LCD PROJECTOR MODEL XL7000U User Manual This User Manual is important to you. Please read it before using your projector. XL7000 U CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: CAUTION: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. [. . . ] opt. SIGNAL A U H V SIGNAL AUTO 1024 x 768 0 0 0 0 AUTO 100% ON ENTER SIGNAL USER 60. 00 Hz 48. 36 KHz 1024 768 OK OK ? MEMORY CALL RESOLUTION (MEMORIZE ) HORIZ. TRACKING RESOLUTION (MEMORIZE) VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES EXECUTE CANCEL CLAMP POSITION CLAMP WIDTH VERT. LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 R RG GB B COMPUTER INPUT OVER SCAN HOLD USER ITEM MEMORY CALL SETTING AUTO / MEMORY 1 MEMORY 2 ) 640-1920 / RESOLUTION (MEMORIZE VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES 350-1200 EXECUTE CANCEL OK OK 0-999 0-999 0-31 0-9999 AUTO RGB YCBCR/YPBPR HORIZ. TRACKING COMPUTER INPUT OVER SCAN HOLD USER CLAMP POSITION CLAMP WIDTH VERT. LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 100%-90% OFF / ON ENTER 1-255 1-63 AUTO / OFF ON / OFF 0-38 0-38 0-63 0-63 FUNCTION Use to select the setting of RESOLUTION (MEMORIZE) already saved. Impossible to select if no setting has been saved. It optimizes the signal format automatically depending on the type of video signal supplied from the computer. Press the ENTER button to clear the setting already saved. To change the current setting, press the ENTER button to display the RESOLUTION (MEMORIZE) menu. The new setting can be saved to MEMORY 1 or MEMORY 2. The vertical frequency of the currently projected video signal is displayed. The horizontal frequency of the currently projected video signal is displayed. The number of horizontal pixels of the currently projected video signal is displayed. When you change the current setting, select EXECUTE, and then press the ENTER button, the image is automatically adjusted according to the resolution you set. The adjustment result can be saved to MEMORY 1 or MEMORY 2. The number of vertical lines of the currently projected video signal is displayed. When you change the current setting, select EXECUTE, and then press the ENTER button, the image is automatically adjusted according to the resolution you set. The adjustment result can be saved to MEMORY 1 or MEMORY 2. Press the ENTER button to start the automatic adjustment. At the completion of the automatic adjustment, a message is displayed and you can save the adjustment result to MEMORY 1 or MEMORY 2. [. . . ] During such a case, the power of the projector isn’t turned on. *4: Status of either or both of the indicators. EN-62 Specifications The specifications and outside appearance of the projector are subject to change without prior notice. Type Model Display technology Projection lens Light-source lamp Image size (projection distance) Maximum resolution Computer signal Video signal Component signal Computer/component video input LCD projector XL7000U 0. 8-inch LCD panel: 3 pieces (for R, G, B) Pixel: 1024 x 768 = 786432 pixels Total 2359296 pixels Active pixel rate: 99. 99% or more (each panel) F 1. 8 - 2. 6 f= 24. 0 - 43. 2 mm 321 W 40” min. (projection distance 1. 2 to 9. 1 m) Maximum resolution:  1920 x 1200 dots (compressed) Panel resolution: 1024 x 768 dots NTSC/PAL/SECAM/4. 43NTSC/PAL-M/PAL-N/PAL-60 480i, 480p, 576i, 576p, 720p, 1080i, 1080p Panel resolution: 1024 x 768 dots [Signal type] [Terminal type] [Line] Analog RGB Mini D-SUB 15-pin 1 Analog RGB 5 BNC 1 Digital RGB DVI-D 24-pin 1 [Signal type] [Terminal type] [Line] Video input BNC 1 S-video input S 1 [Signal type] [Terminal type] [Line] RGB/Component Stereo mini jack (ø3. 5) 2 Digital RGB Stereo mini jack (ø3. 5) 1 Video RCA (L, R) 1 S-video RCA (L, R) 1 [Signal type] [Terminal type] [Line] HDMI HDMI 19-pin 1 [Signal type] [Terminal type] [Line] Analog RGB Mini D-SUB 15-pin 1 [Signal type] [Terminal type] [Line] RGB/Component Stereo mini jack (ø3. 5) 1 10 W Mono Round type x 1 RS-232C (D-SUB 9-pin), LAN (RJ-45), REMOTE IN/OUT (Stereo mini jack (ø3. 5)) +41°F (+5°C) to +104°F (+40°C): ( Standard altitude mode: All projection angles) +41°F (+5°C) to +86°F (+30°C): ( High altitude mode: Floor installation/ceiling installation) AC 100 - 240 V, 50/60 Hz 5. 7 A, 480 W During standby: AC 100 - 120 V: 5  W (when STANDBY MODE is STANDARD) 1. 8 W (when STANDBY MODE is LAN) 0. 2 W (when STANDBY MODE is LOW) AC 220 - 240 V: 5  W (when STANDBY MODE is STANDARD) 1. 8 W (when STANDBY MODE is LAN) 0. 3 W (when STANDBY MODE is LOW) 481 mm (W) x 179 mm (H) x 418 mm (D) (projector only) 481 mm (W) x 179 mm (H) x 502 mm (D) (including the terminal cover) 10. 5 kg (projector only), 11. 0 kg (including the terminal cover) Luminance signal: Vp-p=1. 0 V 75 Ω (negative sync) Chrominance signals: Vp-p=0. 286 V 75 Ω (burst signal) Vp-p=1. 0 V 75 Ω (negative sync) YCBCR: Vp-p=1. 0 V 75 Ω (Y) (negative sync) Vp-p=0. 7 V 75 Ω (CB, CR) RGB: Vp-p=0. 7 V 75 Ω (negative sync) YCBCR: Vp-p=1. 0 V (Y) (negative sync) Vp-p=0. 7 V (CB, CR) HD/CS: TTL-level (negative or positive polarity) VD: TTL-level (negative or positive polarity) DVI-D interface (TMDS single link) with HDCP HDMI interface (TMDS single link) (Only PCM audio is supported. ) 350 mVrms, 10 kΩ or more Video input Audio input HDMI input Monitor output Audio output Speaker Control terminal/others Operating temperatures Rated voltage Power consumption Dimensions (not including protrusion) Weight Others S-video input Video input Component video input Analog input Digital input (DVI) Digital input (HDMI) Audio input Replacement part (option/not included in the box) Spare lamp: VLT-XL7100LP Option lenses: OL-XL7100SZ, OL-XL7100LZ, OL-XL7100TZ, OL-XL7100FR EN-63 Specifications (continued) Specification of RGB signals in each computer mode of the projector Signal mode TV60, 480i (525i) TV50, 576i (625i) 1080i60 (1125i60) 1080i50 (1125i50) 480p (525p) 576p (625p) 720p60 (750p60) 720p50 (750p50) 1080p60 (1125p60) 1080p50 (1125p50) CGA70 CGA84 CGA85 VGA60 VGA72 VGA75 VGA85 SVGA56 SVGA60 SVGA72 SVGA75 SVGA85 SVGA95 XGA60 XGA70 XGA75 XGA85 SXGA70a SXGA75a SXGA85a WXGA60 WXGA60a WXGA60b WXGA60c WXGA+60 WXGA++60 SXGA60b SXGA75b SXGA85b SXGA60 SXGA75 SXGA85 SXGA+60 SXGA+75 WSXGA+60 MAC13 MAC16 MAC19 HP75 HP72 SUN66a SUN76a SUN66 SUN76 SGI72 SGI76 UXGA60 WUXGA60 Resolution (H x V) 720 x 480 720 x 576 1920 x 1080 1920 x 1080 720 x 480 720 x 576 1280 x 720 1280 x 720 1920 x 1080 1920 x 1080 640 x 400 640 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1152 x 864 1152 x 864 1280 x 768 1280 x 800 1360 x 768 1366 x 768 1440 x 900 1600 x 900 1280 x 960 1280 x 960 1280 x 960 1280 x 1024 1280 x 1024 1280 x 1024 1400 x 1050 1400 x 1050 1400 x 1050 1680 x 1050 640 x 480 832 x 624 1024 x 768 1024 x 768 1280 x 1024 1152 x 900 1152 x 900 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1600 x 1200 1920 x 1200 Horizontal frequency (kHz) 15. 73 15. 63 33. 75 28. 13 31. 47 31. 25 45. 00 37. 50 67. 50 56. 25 31. 47 37. 86 37. 86 31. 47 37. 86 37. 50 43. 27 35. 16 37. 88 48. 08 46. 88 53. 67 59. 97 48. 36 56. 48 60. 02 68. 68 63. 85 67. 50 77. 49 47. 78 49. 70 47. 71 47. 50 55. 94 60. 00 60. 00 75. 00 85. 94 63. 98 79. 98 91. 15 63. 98 65. 32 82. 28 65. 29 35. 00 49. 72 60. 24 62. 94 78. 13 61. 85 71. 81 71. 68 81. 13 76. 92 82. 01 75. 00 74. 04 Vertical frequency (Hz) 59. 94 50. 00 60. 00 50. 00 59. 94 50. 00 60. 00 50. 00 60. 00 50. 00 70. 09 84. 13 85. 08 59. 94 72. 81 75. 00 85. 01 56. 25 60. 32 72. 19 75. 00 85. 06 94. 89 60. 00 70. 07 75. 03 85. 00 70. 01 75. 00 85. 06 59. 87 59. 81 60. 02 59. 75 59. 89 60. 00 60. 00 75. 00 85. 00 60. 02 75. 02 85. 02 60. 02 59. 98 74. 87 59. 95 66. 67 74. 55 75. 02 74. 92 72. 00 66. 00 76. 64 66. 68 76. 11 72. 30 76. 00 60. 00 59. 95 Normal mode (H x V) 1024 x 768 1024 x 768 1024 x 576 1024 x 576 1024 x 768 1024 x 768 1024 x 576 1024 x 576 1024 x 576 1024 x 576 1024 x 640 1024 x 640 1024 x 640 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 614 1024 x 640 1024 x 578 1024 x 576 1024 x 640 1024 x 576 1024 x 768 1024 x 768 1024 x 768 960 x 768 960 x 768 960 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 640 1024 x 768 1024 x 768 1024 x 768 1024 x 768 960 x 768 984 x 768 984 x 768 960 x 768 960 x 768 960 x 768 960 x 768 1024 x 768 1024 x 640 *1 *1 *1, *2, *3 *1, *2, *3 *1, *2, *3 *1, *2, *3 *1, *2, *3 *1, *2, *3 *1, *2, *3 *1, *2, *3 *2, *3 *2, *3 *2, *3 *2 *2, *3 *2, *3 *2, *3 *2, *3 *1: The PinP mode, the MAGNIFY mode and IMAGE CAPTURE in the INSTALLATION menu don’t function with these signals. *2: The COMPUTER/COMPONENT/VIDEO DVI-D IN (HDCP) terminal is available for these signals. [. . . ]