User manual MOFFAT GSC5050W

[. . . ] GAS COOKER GSC 5050 W GSC 5050 WL GB 2 CONTENTS Instructions for the user Important Safety Information Description of the appliance Technical Features Using the appliance - Using the oven - Hints & Tips - Using the Grill - Using the Hob Maintenance and Cleaning Something Not Working Service & Spare Parts Customer Care Guarantee conditions 4 5 6 7 7 9 10 11 13 15 16 16 17 Instructions for the installer Safety Advice Technical Data Installation - Positioning - Ventilation - Location Gas connections Conversion of gas 18 18 19 19 20 20 21 23 How to read the instruction book The symbols below will guide you when reading the instruction book Safety instructions Step by Step Operation Advice and recommendations Environmental Information 3 IMPORTANT SAFETY INFORMATION You MUST read these warnings carefully before installing or using the appliance. If you need assistance, contact our Customer Care Department on 08705 950950. Installation · This cooker must be installed by qualified personnel, according to the manufacturer's instructions and to the relevant British Standards. · Any gas installation must be carried out by a registered CORGI installer. · Remove all packaging before using the cooker. [. . . ] Off Maximum level Minimum level Use the maximum level for boiling and the minimum for simmering. Always choose positions between the minimum and maximum, never between maximum and off. Do not close the lid if the hob is hot, the lid could be damaged. A build-up of fats or other foodstuffs could result in a fire, especially in the grill pan. Before cleaning, ensure all control knobs are in the OFF position, and the appliance has cooled completely. Cleaning materials Before using any cleaning materials on your oven, check that they are suitable and that their use is recommended by the manufacturer. Cleaners that contain bleach should NOT be used as they may dull the surface finishes. External cleaning Regularly wipe over the control panel, oven door and door seal using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. To prevent damaging or weakening the door glass panels avoid the use of the following: · Household detergent and bleaches · Impregnated pads unsuitable for non stick saucepans · Brillo/Ajax pads or steel wool pads · Chemical oven pads or aerosols · Rust removers · Bath/Sink stain removers Oven Door The door can be dismantled for cleaning as follows: - Open the door completely. - Revolv the two locking parts on the hinge arms completely upwards. - Partially close the door, to a 30o angle. The internal oven door glass can be removed for cleaning. For this purpose remove the 2 fixing screws. Clean the outer and inner door glass using warm soapy water. Should the inner door glass become heavily soiled it is recommended that a cleaning product such as Hob Brite, or Bar Keepers Friend be used. locking parts DO NOT clean the oven door while the glass panels are warm. If this precaution is not observed the glass panel may shatter. If the door glass panel becomes chipped or has deep scratches, the glass will be weakened and must be replaced to prevent the possibility of the panel shattering. Contact your local Service Centre who will be pleased to advise further. IMPORTANT: The inner door glass must be in place when using the oven. 13 Oven Cavity The enameled oven cavity is best cleaned whilst the oven is still warm. Wipe the oven over with a soft cloth soaked in warm soapy water after each use. From time to time it will be necessary to do a more thorough cleaning, using a proprietary oven cleaner. Hob After every use wipe with a soft cloth well wrung out in warm water to which a little washing up liquid has been added, avoiding any leakage through the holes of the hob. To remove more stubborn stains, wet and leave to dissolve, do not scratch and avoid the use of abrasive or caustic products that could damage the enamel. Burners The burner caps and crowns can be removed for cleaning. [. . . ] Check that, turning the knob quickly from the maximum position to the minimum one, the flame does not go out. 23 Hob burners To adjust the minimum level: · Light the burner · Turn the knob to the position of the minimum flame; · Remove the knob; · Unscrew or screw the by-pass screw (on the left above of tap shaft) until a regular small flame is reached. · For LPG, adjust the by-pass screw for minimum flame setting. Reassemble the parts following the same procedure in reverse. Check that, when turning the knob quickly from the maximum position to the minimum one, the flame does not go out. [. . . ]