User manual MOFFAT MG35B

[. . . ] Remove all packaging before using the hob. Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. Do not attempt to modify the hob in any way. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. [. . . ] Do not use this hob if it is in contact with water. after cleaning. Service and Spare Parts Guarantee Conditions If you require spare parts or an engineer contact your local Service Force Centre by telephoning: We, Moffat, undertake that if, within 12 months of the date of the purchase, this Moffat appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate. * The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's instructions. * The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. * All service work under this guarantee must be undertaken by a Moffat Service Force Centre. * Any appliance or defective part replaced shall become the Company's property. * This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8. 30am and 5. 30pm Monday to Friday. Visits may be available outside these hours, in which case a premium will be charged. 08705 929 929 Your call will be routed to the Service Centre covering your post code area. CUSTOMER CARE For general enquiries concerning your Moffat appliance and for further information on Moffat products, contact our Customer Care Department by letter or telephone as follows: Customer Care Department Moffat 55-77 High Street Slough Berkshire SL1 1DZ Tel : 08705 950950 * calls to this number may be recorded for training purposes Exclusions This guarantee does not cover: * Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. * Costs incurred for calls to put right an appliance which is improperly installed or calls to appliance outside the United Kingdom. However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m3. If there are other fuel burning appliances in the same room, B. S. 5440 Part 2 Current Edition, should be consulted to determine the requisite air vent requirements. Location The hob may be located in a kitchen, a kitchen/ diner or bed sitting room, but not in a bathroom, shower room or garage. Before making the cut out in the worktop ensure that the edges of the hob that are to be near either a side or rear wall have a minimum distance of 55 mm. between the edge of the hob and the wall. The minimum distance combustible material can be fitted above the hob is 400 mm. must be allowed from the edges of the hob. The minimum distance combustible material can be fitted directly above the hob is 700 mm. must be left between the side edges of the hob and any adjacent cabinets or walls. 650 mm FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE 700 mm 400 mm 55 mm 50 m m 400 mm 100 mm 50 m m FO 0812 FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 600 mm 400 mm 50 m 55 m mm 400 mm 100 mm 50 m m FO 0813 When the hob is first installed Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. [. . . ] size Cable/flex 0. 75 mm 2 Cable / flex type H05 V2V2-F (T90) Fuse 3A 1. Connect the green and yellow (earth) wire to the terminal in the plug which is marked with the letter 'E' or the earth symbol or coloured green and yellow. The earth wire should be about 2 cm longer than the neutral and live wires. Connect the blue (neutral) wire to the terminal in the plug which is marked with the letter 'N' or coloured black. [. . . ]