User manual MOFFAT MSC5061W

[. . . ] MIXED FUEL COOKER MSC 5061 W GB 2 CONTENTS Instructions for the user Important Safety Information Description of the appliance Technical Features Using the appliance - Using the electric oven - Using the electric grill - Hints & Tips - Using the Hob Maintenance and Cleaning Something Not Working Service & Spare Parts Customer Care Guarantee conditions 4 5 6 7 7 8 9 10 12 14 Conversion of gas 15 15 16 Instructions for the installer Safety Advice Electrical connection Technical Data Installation - Positioning - Ventilation - Location Gas connections - Electrical connection 17 18 19 19 19 20 20 21 23 24 How to read the instruction book The symbols below will guide you when reading the instruction book Safety instructions Step by Step Operation Advice and recommendations Environmental Information 3 IMPORTANT SAFETY INFORMATION You MUST read these warnings carefully before installing or using the appliance. If you need assistance, contact our Customer Care Department on 08705 950950. Installation · This cooker must be installed by qualified personnel, according to the manufacturer's instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. [. . . ] Release the knob and watch that the burner has ignited. Upon ignition, adjust the flame as required. · OR Lack of power · Push the corresponding knob in completely and turn it left to the "large flame" symbol and ignite with a match. · Release the knob and watch that the burner has ignited. Upon ignition, adjust the flame as required. · If for any reason the flame should extinguish turn off the relevant control know, leave for at least one minute and then re-ignite. Extinguishing of burners Turn the knob clockwise to mark « 10 ». Do not put anything on the hob that is liable to melt. Selecting the Correct burner Above every knob there is a symbol for the corresponding burner. For good cooking results, always choose pans, which correctly fit to the diameter of the burner used (see figs). - Partially close the door, to a 30o angle - Lift the door and pull out The internal oven door glass can be removed for cleaning. For this purpose Clean the outer remove the 2 fixing screws. and inner door glass using warm soapy water. Should the inner door glass become is recommended that a heavily soiled it cleaning product such as Hob Brite, or Bar Keepers Friend be used. Always support the door while removing the glass panel as the door may spring closed due to its lighter weight. 12 locking parts DO NOT clean the oven door while the glass panels are warm. If this precaution is not observed the glass panel may shatter. If the door glass panel becomes chipped or has deep scratches, the glass will be weakened and must be replaced to prevent the possibility of the panel shattering. Contact your local Service Centre who will be pleased to advise further. IMPORTANT: The inner door glass must be in place when using the oven. Oven Cavity The enamelled oven cavity is best cleaned whilst the oven is still warm. Wipe the oven over with a soft cloth soaked in warm soapy water after each use. From time to time it will be necessary to do a more thorough cleaning, using a proprietary oven cleaner. Hob After every use wipe with a soft cloth well wrung out in warm water to which a little washing up liquid has been added, avoiding any leakage through the holes of the hob. To remove more stubborn stains, wet and leave to dissolve, do not scratch and avoid the use of abrasive or caustic products that could damage the enamel. Burner cap Burners The burner caps and crowns can be removed for cleaning. Wash the burners caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well-moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. [. . . ] · Adjust the legs as necessary. 1 5 4 3 2 20 GAS CONNECTIONS Your cooker is delivered adjusted for the kind of gas stated on the rating plate If the appliance is supplied with natural gas and the pressure for natural gas is 20mbar. The following methods of connection to the gas supply must be used: Right Hand Connection (from front) Ensure that the rubber hose is not in contact with any part of the hatched area shown in the diagram and that the loop of the hose when connected is not in contact with the floor when the appliance is in position. BACK OF THE COOKER power cord connection of flexible hose clamps BACK OF THE COOKER Left Hand Connection (from front) Ensure that the rubber hose is not in contact with any part of the hatched area shown in the diagram and the hose is retained in the clamp provided, it will be necessary to fit the maximum length hose when using this method. power cord connection of flexible hose Rigid Connection Where it is not possible to make the connection using a rubber hose, a rigid pipe work connection must be used. clamps Recommendations when using an appliance flexible connector are as follows: - For NATURAL the gas installation pipes to the termination point shall comply with: Specification for installation of low-pressure gas pipe work of up to 20mm (R1) in domestic premises (2nd family gas) ­ BS 6891; Connection shall be by means of an appliance flexible connector for use with a self-sealing plug-in device, complying with: Flexible hoses, end fittings and sockets for gas burning appliances ­ BS 669; 21 The appliance flexible connector should not be subjected to undue forces either in normal use or whilst connected or disconnected; - The socket which the plug of the appliance flexible connector fits should be permanently attached to a firmly fixed gas installation pipe and positioned such that the appliance flexible connector hose hangs freely downwards (see fig. ); - The appliance flexible connector should be positioned such that it will not suffer mechanical damage, e. g. abrasion from the surrounding kitchen furniture, which may be moved in use such as a drawer or door, or by being trapped by any stability device. The plug-in-connector should be accessible for disconnection after moving the appliance. 22 Electrical connection Important In any connection way the appliance has to be grounded, in accordance with the national rules in force. We decline any responsibility in case of accidents due to no grounding or wrong grounding. [. . . ]