User manual MOFFAT MUL514

[. . . ] User Manual Refrigerator MUL 514 Thank you for choosing a Moffat household appliance. Convince yourself: Our products are reliable. We wish you lots of enjoyment with your new appliance and we hope you consider Moffat again for future purchases. Please read this user manual carefully and keep it for future reference. The user manual should be passed on to any future owner of the appliance. Content Safety information - - - - - - - - - - - - - - - - - - -3 Before use - - - - - - - - - - - - - - - - - - - - - - - -5 Setting the temperature - - - - - - - - - - - - - - -5 Fresh food refrigeration - - - - - - - - - - - - - - -5 The door shelves - - - - - - - - - - - - - - - - - - -6 Normal operating sounds - - - - - - - - - - - - - -6 Health and Safety Guidelines - - - - - - - - - - -6 Cleaning and care- - - - - - - - - - - - - - - - - - - 7 When the appliance is not in use - - - - - - - - 7 Internal cleaning - - - - - - - - - - - - - - - - - - - - 7 Periodic cleaning - - - - - - - - - - - - - - - - - - - 7 Changing the light bulb - - - - - - - - - - - - - - - 8 Defrosting- - - - - - - - - - - - - - - - - - - - - - - - - 8 Environmental concerns - - - - - - - - - - - - - - 8 Something not working - - - - - - - - - - - - - - - 9 Service and Spare Parts - - - - - - - - - - - - - 10 Guarantee conditions - - - - - - - - - - - - - - - 10 Technical data- - - - - - - - - - - - - - - - - - - - - 12 Electrical connection - - - - - - - - - - - - - - - - 12 Installation - - - - - - - - - - - - - - - - - - - - - - - 13 Positioning - - - - - - - - - - - - - - - - - - - - - - - 14 Door reversal - - - - - - - - - - - - - - - - - - - - - 14 Building-in instructions- - - - - - - - - - - - - - - 15 2 Safety information It is most important that this instruction book should be retained with the appliance for future reference. [. . . ] Clean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed, so that the defrost water may flow freely. Periodic cleaning The appliance is equipped with a ventilation grid. Keep clean to guarantee good ventilation and good working order of the appliance. An accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. The structure of the appliance permits cleaning of the rear zone close to the wall, using a vacuum cleaner. Remove the plinth (1), then the ventilation grid (2); 2. Carefully pull the air deflector out (3) checking that there is no water left from the defrosting. 3 2 1 S. I. 013 7 Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply, then replace the bulb as follows: 1. Unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest Service Force centre). Replace the light cover by sliding it into its original position and replacing the screw. Defrosting The refrigerator automatically defrosts every time the compressor stops. The light does not come on Ensure that the bulb is correctly fitted. Check the door light switch is not jammed. The temperature in the fridge or Check the ambient temperature is within the appliances freezer section is too high operating limits of 10°C to 38°C. Check the thermostat control knob is turned to the correct setting relative to ambient conditions. Adjust the thermostat control knob to give correct The compressor runs temperature control. continuously Check that the door is closed. Large quantities of food have recently been placed in the cabinet and/or door is frequently opened. Check that air ventilation is not obstructed. Excessive frost and ice has built Ensure the door is not left open. Check that nothing is preventing the door from closing. No power to appliance Water under the salad bins Check the drain hole is not blocked. (see Maintenance and Cleaning). If after the above checks, there is still a fault, call your local Service Force Centre. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. [. . . ] in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdryer on a low setting. 14 Building-in instructions Before carrying out any work, remove the plug from the power socket. Installation kit 1xB 2xC Grid preparation Left door opening: Remove the left side (A) of the grid cutting it from the rear (see figure). A B 1xA 1xK 2xG 2xL 2xF 2xD 18xI 2xE DO002/2 Right door opening: Remove the right side (B) of the grid cutting it from the rear (see figure). To position the grid on the appliance proceed as follows: Apply the grid to the base of the appliance by pushing on to the clasps (a) until they click. 60 0 1. [. . . ]