User manual MORPHY RICHARDS BAGLESS UPRIGHT VACUUM CLEANER 73281

[. . . ] 73281 rev1 13/3/08 16:22 Page 1 Bagless upright vacuum cleaner Please read and keep these instructions Getting the best from your new cleaner. . . If your cleaner is not picking up as well as it should, please check Dust canister It is important to regularly empty the canister, even if it does not appear full. Filters It is important that the dust canister pleated/mesh filter is tapped clean over a dustbin each time the dust canister is emptied, this allows air through the appliance. Wash the canister filters regularly in luke-warm water and allow to air dry before re-fitting. Blockages Check the hose, tubes and tools for blockages. Safety cut-out If the air-flow is blocked or the filters are not regularly cleaned, a thermostat may operate. If this happens, switch off and disconnect from the mains supply. Clear any blockage, empty and clean the filters. [. . . ] Insert the hose clip  into it's slot in the rear of the appliance. 2 E 4 UK Helpline 0844 871 0949 Replacement Parts 0844 873 0715 Ireland Helpline 1800 409 119 73281 rev1 13/3/08 16:22 Page 5 Using on carpets 1 2 Place the cleaner in it's upright position. Set the carpet height adjustment dial · to the desired position. Release the mains cable by revolving the quick release cleat half-a-turn and extend the cable fully. Step on the handle release pedal to release the handle to the desired position. Press the ON/OFF button to the `ON' position. IMPORTANT: To prevent damage to carpets: · Never leave the cleaner switched on in one place for an extended period. Never have the brushes set too low such that the cleaner is hard to push. Never lean on the product. 6 If additional length is required, remove the telescopic tube from the cleaner, connect it to the handle, and add the desired accessory to the end of the tube G. IMPORTANT: When using the hose and tools, locate the hose into the hose hook Ï on the main unit. This will help prevent the cleaner from tipping over. IMPORTANT: Turning the cleaner sideways helps prevent the cleaner being pulled along by the stretched hose. F 3 7 · 4 5 · 6 Using & cleaning the turbo nozzle Attach the Turbo nozzle to either the handle or the telescopic tube as described previously. Following use, your turbo nozzle may become clogged. Turn over the tool and pull away any hairs or fibres. If they are tightly wound around the brush, carefully snip the fibres with scissors, being careful not to damage the brush bar, pull away from the brush bar and dispose. · · Using the attachments Follow steps 1-4 of the `Using on carpets' section, but set the carpet height adjustment dial to the tools setting. 5 Attach the accessories , , , to the handle, removing the handle from the telescopic tube, then firmly push in the desired accessory F: Turbo tool , is ideal for pet hair removal from stairs and upholstery. Upholstery tool , , for upholstery, stairs etc. Crevice tool for awkward places, corners and behind radiators etc. SAFETY CUT-OUT If the cleaner overheats, a motor protection thermostat will automatically switch the motor off. If this happens, switch the cleaner off, unplug from the power supply and leave the cleaner to cool for at least 60 minutes. Check the airways for blockages, empty the dust canister and clean the filters before restarting. G www. morphyrichards. com 5 73281 rev1 13/3/08 16:22 Page 6 H Ê EMPTYING THE DUST CANISTER Empty the dust canister regularly even if it does not look full, this will maintain the performance. IMPORTANT: Always empty the dust canister and clean the filter and mesh following prolonged use. Clean the filter and mesh screen every time the dust canister is emptied. I 1 2 Unplug the cleaner from the mains switch. Press the dust canister release button Ê and pull the canister away from the main body H. Hold the dust canister over the dustbin. [. . . ] Please quote the following information if the product develops a fault. These numbers can be found on the base of the product. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase, it should be returned to the place of purchase for it to be replaced. [. . . ]