User manual MORPHY RICHARDS IB40460

[. . . ] 5 Morphy Richards are not liable to carry out any type of servicing work, under the guarantee. 6 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. All Morphy Richards Products are individually tested before leaving the factory. [. . . ] 10 Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down - there may be hot water in the reservoir. SPECIAL INSTRUCTIONS 1 If your iron does not work, check the following points: Has the temperature control been set to the required temperature?Is the plug itself or the socket faulty?(Check by plugging in another appliance) 2 Warning: When in use, your iron should never be placed flat and left on an ironing board. 3 To prevent damage to the textile being ironed, follow the temperature guide carefully. (Test the inside of the hem of the garment). 4 When ironing is complete, remove the plug from the socket, empty any remaining water from the tank, and allow to cool before storing. 5 If you drop or severely knock your iron this could cause internal damage even if the outside appears alright. Have it checked by a qualified electrician. 6 It is recommended that you use up one beaker of water by operating your iron's steam function before ironing any clothes as some dripping may occur while your iron's steam system is activated. SAVE THESE INSTRUCTIONS 2 Electrical requirements Components of your iron Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance, the plug should be removed and the appropriate one fitted. WARNING: The plug removed from the mains lead, if severed, must be destroyed as a plug with bared flexible cord is hazardous if engaged into a live socket outlet. WARNING: THIS APPLIANCE MUST BE EARTHED Should the fuse in the 13 amp plug require replacement, a BS1362 13 amp fuse must be fitted. flfi / ¤ < > / Temperature control dial ¤ Temperature indicator light < Water filler hole > Soleplate fi Spray button (certain models only) fl On-off steam button Water tank viewing window Instructions for use Temperature Guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol Control knob positions Fabric 6 Do not iron at all 7 (120°C Max) Cool q Nylon, Acetates E. g. Acrilan Courtelle, Orlon, Triacetates, e. g. If moisture required use damp cloth (Not Acetate) 8 (160°C Max) Warm qq Wool, Polyester mixtures e. g. Polyester/Cotton 9 (210°C Max) Hot qqq Cotton, Linen Rayon, Rayon mixtures, e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc Steam/spray Dry ironing Ironing With water in tank Without water in tank Dry and Spray 3 Before use Note: The Steam facility should only be used on garments which are suitable for ironing at the 3 dot setting. Textiles and clothes are supposed to carry ironing instructions. If they don't you should follow the temperature guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Temperature control Plug in the iron and switch on. Set the heat control dial B to the temperature required, but don't start ironing immediately. [. . . ] Before you start ironing, slide the steam button up to the steam position D. If you need to refill the water tank during use, unplug the iron and follow the filling instructions taking care not to Steam on spill any water over the iron. F D Emptying and storing When you have finished ironing unplug your iron. Ensure that the steam button is down, in the `Steam off' position E and empty any remaining water out of the Steam off filler hole F. Do not store in the box, but in an upright position, so that any drops of water remaining cannot leak out and discolour the soleplate. [. . . ]