User manual MORPHY RICHARDS IB42700

[. . . ] 5 Morphy Richards are not liable to carry out any type of servicing work, under the guarantee. 6 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. All Morphy Richards Products are individually tested before leaving the factory. [. . . ] (Test the inside of the hem of the garment). 4 When ironing is complete, remove the plug from the socket, empty any remaining water from the tank, and allow to cool before storing. 5 If you drop or severely knock your iron this could cause internal damage even if the outside appears alright. Have it checked by a qualified electrician. 6 It is recommended that you use up one beaker of water by operating your iron's steam and shot of steam functions before ironing any clothes as some dripping may occur while your iron's steam system is activated. SAVE THESE INSTRUCTIONS 2 Electrical requirements Components of your iron Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance, the plug should be removed and the appropriate one fitted. WARNING: The plug removed from the mains lead, if severed, must be destroyed as a plug with bared flexible cord is hazardous if engaged into a live socket outlet. WARNING: THIS APPLIANCE MUST BE EARTHED Should the fuse in the 13 amp plug require replacement, a BS1362 13 amp fuse must be fitted. < fifl/ ¤ > / Temperature control dial ¤ Temperature indicator light < Water tank cap > Soleplate fi Spray button (certain models only) fl Shot of steam button (certain models only) Steam on-off button/variable steam button Instructions for use Temperature Guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol Control knob positions Fabric 6 Do not iron at all 7 (120°C Max) Cool q Nylon, Acetates E. g. Acrilan Courtelle, Orlon, Triacetates, e. g. If moisture required use damp cloth (Not Acetate) Dry and Spray 8 (160°C Max) Warm qq Wool, Polyester mixtures e. g. Polyester/Cotton 9 (210°C Max) Hot qqq Cotton, Linen Rayon, Rayon mixtures, e. g. Rayon/Linen Ironing With water in tank Without water in tank Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc Steam/spray & shot Jet clean Dry ironing 3 Before use Note: The Steam facility should only be used on garments which are suitable for ironing at 2 and 3 dot settings. (Garments marked with 2 dot recommendation should, if required, be ironed at the lower end of the steam range). Textiles and clothes are supposed to carry ironing instructions. If they don't you should follow the temperature guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Temperature control Plug in the iron and switch on. Set the temperature control dial C to the temperature required, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at ST E the required setting. EAM RA N G Your Morphy Richards iron is fitted with an indicator light which will go on and off while your are ironing. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. For the correct temperature always set the control dial with the required setting at the bottom of the dial nearest the back of the iron. C Filling Before filling your iron make sure that it is not plugged in and ensure that the iron is in the `steam off' position. [. . . ] The high position is for ironing stubborn creases F High steam Auto shut-off (certain models only) If your iron is an `auto shut-off' model it will automatically turn your iron off within 60 seconds of not being used. Grasping the iron by its handle will turn it on again. If the iron is below the temperature set on the temperature control dial, the temperature indicator light will illuminate until the iron reaches the set temperature. AUTO SHUT-OFF IS NOT AN ALTERNATIVE TO UNPLUGGING THE IRON WHEN NOT IN USE. The mid position is for normal ironing Low steam The low position switches the steam off. Steam off 5 Emptying and storing When you have finished ironing unplug your iron. [. . . ]