User manual MORPHY RICHARDS IB47010

[. . . ] 47010 rev2 24/4/06 15:10 Page 1 Mister Cappuccino Espresso and filter coffee maker with heated milk frother Please read and keep these instructions Getting the best from your new coffee maker. . . WARNING : pressure cap on espresso Unplug your coffee machine. The pressure cap must be slowly removed before unlocking the filter holder. Safety first Caution must be used when handling hot water, coffee or steam. Run water through your machine before first use It is important to run water through your coffee maker in order to rinse the machine. You can also run water through to warm your coffee machine. Descale as appropriate for the hardness of the water in your area It is important to descale as the performance of your coffee maker may be impaired by limescale and other impurities in the water supply. For replacement parts, help with using your Morphy Richards, problems and lots more, contact us by phone or through our website. UK Helpline: 0870 060 2610 Replacement parts: 0870 167 6641 Ireland 1800 409119 CM47010 Rev 2 www. morphyrichards. com 47010 rev2 24/4/06 15:10 Page 2 IMPORTANT SAFETY INSTRUCTIONS The use of any electrical appliance requires the following common sense safety rules. [. . . ] A NOTE: Push firmly to the right to lock into position. 6 Your machine is fitted with a strength selector < which allows you to make LIGHT to STRONG coffee. Set the strength selector mid way between LIGHT and STRONG for MEDIUM strength coffee. Place your glass jug with the lid on the drip tray and · directly under the spout of the filter holder, ensuring that the jug handle is pointing outwards from the unit. Press the on/off switch , , to `ON' and the orange light will glow. The coffee will start to flow from the filter holder spout after about 2 or 3 minutes. Wait until all the water from the water tank has flowed into your glass jug and the green light glows. Set the on/off switch to `OFF'. 9 When the filtering process is complete remove the glass jug from your coffee maker and pour the coffee into your cups. 2 10 Unplug machine and allow to cool. 11 To remove the used coffee grounds, remove the filter holder by turning the handle to the left until you find that the filter holder drops down. Flip the filter retaining clip fi so that it retains the filter. Turn the filter upside down and knock out the grounds. Flip the retaining clip back along the handle before the next use. Do not exceed the maximum level or add less than the minimum level. Place the jug on the hot plate and switch on. D NOTE: You can turn on the hot plate at the same time as the coffee on/off switch. It will take approximately 5-7 minutes for the milk to heat up to its optimum frothing temperature. 2 3 F Lift the milk jug up to the milk frother blade E. Raise the milk jug ensuring that the cowl is just under the surface of the milk - this will give the maximum froth. Maintain the milk jug in this position between 30-60 seconds. WARNING: Take care as the milk will be hot. 4 Place the milk jug back on the hot plate to reheat the milk and preserve the quality of the froth. NOTE: The jug can stay on the hot plate until the coffee has finished brewing but be careful not to burn your milk/froth. G 5 Pour the coffee into cups and gently pour or preferably spoon the milk onto the coffee, then sprinkle a little chocolate powder for the perfect cappuccino. Turn off the milk frother hot plate by pressing the on/off switch. WARNING: the stainless steel jug and the hotplate will remain hot for sometime after switching off. 6 www. morphyrichards. com 7 47010 rev2 24/4/06 15:10 Page 8 FILTER RECIPES Cafe Melange 2 parts coffee Irish coffee Makes 4 servings 75ml of double cream 1 part hot milk 4 tsp sugar Dollop whipped cream 8 shots of Irish whiskey 1 Prepare filter coffee as per `making coffee' instructions. [. . . ] Staple your receipt to this back cover for future reference. Please quote the following information if the product develops a fault. These numbers can be found on the base of the product. 2 All Morphy Richards products are individually tested before leaving the factory. [. . . ]