User manual MORPHY RICHARDS IB75221

[. . . ] · Do not insert pins or any sharp objects into the blanket. · Do not tuck the heated part of material under the mattress. · Do not use if the blanket is wet. · Avoid pressing creases or folds into the blanket. [. . . ] Do not connect both leads to one 13amp plug. The two leads should preferably be plugged into individual sockets. However, if only one socket is accessible, then a dual adaptor should be used. WARNING: Only the electric blanket should be connected to the dual 3 Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 4 Fitting instructions Fitted underblanket with elasticated corner tapes 1 Place the mattress cover directly on the mattress with the control switch end at the head of the bed. 2 Turn the elastic corners underneath the mattress to secure in place (see diagram A). 3 Ensure all creases are smoothed out. A Switch control Note: Braille markings are located on the back of the switch. , These three settings automatically turn the heat off after the selected time 12 hours 3 hours 1 hour / Power 'ON' light · Automatically switches the blanket on 3 hrs before you go to bed High heat setting (PRE-HEAT) ¤ Low heat setting (ALL NIGHT) < Heat setting Timer & 'Off' selection slider indicator Red = High heat Green = Low heat fl Blanket 'Off' position fi Sleep button Allows you to re-heat the bed through the night once a timer setting has switched off. > Heat selection slider 4 Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 5 How to use 1 Ensure the blanket is fitted to the bed correctly. 2 Plug the power lead into the closest socket, using an extension lead if needed to ensure that the lead is not stretched. Sleep button 1 Use this button to turn the heat on for 30 minutes when the timer has switched the heat off. 3 The small light at the base of the switch will flash to indicate that the sleep function has been activated. 4 After 30 minutes the light will stop flashing and the heat will switch off. · Note: This function will only operate if the blanket is switched to a timer off setting, which has reached the end of the time period. It will not work if the switch is at the OFF 'O' position. Preheating the bed 1 Turn the blanket on by setting one of the timer off settings /, < or Â. 2 Set the heat setting on the control switch to maximum heat, the light indicator will show a red light to indicate that the preheating has been selected. Allow approximately 10-20 minutes for a light heat and a further 20-30 minutes for the blanket to heat the bed thoroughly, although this time may vary depending on room temperature. Setting the timer 1 To program the heat to turn on in 3 hours time, move the timer button to the unfilled 3 symbol . Ensure that the heat setting is set to pre-heat, maximum heat level. 2 When you get into bed, change the heat level to low, all night level. The heat will turn off after 9 hours, unless an alternative timer off setting or the OFF 'O' position is selected. 3 To program the heat to turn off after a set number of hours, move the timer button to the filled hour symbol /<Â. For example, set to turn heat off after 1 hour, move the button to /. Ensure that the heat setting is set to a low, all night level. Note: The timer function will switch the blanket off after the selected time. Timer must be switched to the OFF position before setting a further time. All night use 1 Select the required timer off setting /, < or  hours. 2 Set the heat setting on the control switch to LOW heat, the heat setting indicator will show a green light. [. . . ] For further help and advice, please contact our Helpline. Helpline Should you need any advice on using the product, please contact our helpline, 8:30 - 5:00 Mon - Thurs 8:30 - 4:00 Fri Tel: 0870 060 2616 0870 060 2616 1800 409089 Alternatively, please write to Morphy Richards Consumer Care or email us on: customercare@morphyrichards. co. uk 7 Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 8 Your three year guarantee It is important to retain the retailers receipt as proof of purchase. Staple your receipt to this back cover for future reference. Please quote the following information if the product develops a fault. These numbers can be found on the rating label attached to the blanket. [. . . ]