User manual MORPHY RICHARDS IB75300

[. . . ] · Do not insert pins or any sharp objects into the blanket. · Do not tuck the heated part of material under the mattress. · Do not use if the blanket is wet. · Avoid pressing creases or folds into the blanket. [. . . ] However, if only one socket is accessible, then a dual adaptor should be used. WARNING: Only the electric blanket should be connected to the dual 3 S5 Rev 2 21/7/04 1:54 PM Page 4 Overblanket · Your overblanket should as the name suggests, be used ABOVE not underneath the occupant of the bed. It can be used either under a duvet or one or two blanket covers. It can also be used inside the duvet cover. Inside the duvet cover The overblanket is designed to enable it to be placed inside the duvet cover with a duvet of up to 12. 5 tog if desired. 1 It should be carefully inserted into the duvet cover BELOW the duvet, ensuring that it is spread smoothly and that there are no folds in the overblanket (see diagram B). 2 Securing loops are provided along the top edge of the overblanket. These can be used to sew it to the duvet with a simple stitch to help prevent the blanket from moving inside the duvet cover. · If the duvet cover is smaller than normal size it is permissable for the side edges of the overblanket (no more than 3" or 75mm) to be folded over to allow it to fit inside the duvet cover. WARNING: On no account should the central, heated area of the blanket be folded for this purpose. The electric lead should be located at the open end of the duvet cover at the bottom of the bed. Under the duvet cover 1 The bed should be made as normal, with a bottom sheet covering the mattress then a top sheet above the bed occupant, then the heated overblanket, then the duvet or covers (see diagram A). 2 Fold the top sheet over top edge of the blanket and tuck in sides. WARNING: Do not fold over the top part of the blanket or tuck in any wired parts. A B Heated overblanket Heated overblanket 4 S5 Rev 2 21/7/04 1:54 PM Page 5 Switch control Features / Illuminated heat setting light (Red for preheat level, green for safe all night level) ¤ Variable heat levels (For exact heat preference) < Braille markings (located on the back of the switch) > Timer off (Automatically turns the heat off after the number of hours selected) fi Timer on (Automatically turns the heat on in 3 hours time) fl Off setting Power `on' indicator light > ¤ < fi fl / How to use 1 Ensure the blanket is fitted to the bed correctly. 2 Plug the power lead into the closest socket, using an extension lead if needed to ensure that the lead is not stretched. All night use 1 Select the required timer off setting. 2 Set the heat setting on the control switch to the low/minimum heat, the light indicator will show a green light to indicate that the all night setting has been selected. · This setting will provide safe and comfortable heat to sleep on all night. · This setting can be used to air the bed. WARNING: Always ensure that the heat setting is moved to the OFF position when you get up the next day. Preheating the bed 1 Turn the blanket on by selecting one of the timer off settings /, < or Â. 2 Move the heat setting on the control switch to maximum heat, the light indicator will show a red light to indicate that the preheat setting has been selected. Allow approximately 10-20 minutes for a light heat and a further 2030 minutes for the blanket to heat the bed thoroughly, although this time may vary depending on room temperature. Braille markings · Braille markings are located on the back of the switch to help identify the direction of the heat level in the dark, or if visually impaired. · The highest heat level pre-heat is identified by 3 raised nodules mid level by 2 raised nodules low level (all night) by 1 raised nodule. 5 S5 Rev 2 21/7/04 1:54 PM Page 6 Setting the timer 1 To program the heat to turn on in 3 hours time, move the timer button to the unfilled 3 symbol . Ensure that the heat setting is set to pre-heat, maximum heat level. 2 When you get into bed, change the heat level to low, all night level. [. . . ] If the blanket fails to operate, check the following before returning: 1 Ensure that the plug and socket have not become disconnected. 2 Check that the supply plug is correctly connected to the flex. 3 Check the supply fuse and the 3 amp plug fuse if applicable. Service department Waterside Mill Langham Street Rosegrove Burnley BB12 6AL Republic of Ireland c/o Dimpco Ltd Airport Road Cloghran Co. [. . . ]