User manual MORPHY RICHARDS IB75400

[. . . ] · Do not leave the pad in contact with the skin for excessive periods of time. · Overlong application at a high setting can result in skin burns. · Should the pad feel hot, switch down to the next lowest heat setting or switch off. · Never place additional objects such as hot water bottles or pillows on the heated area. [. . . ] It is normal for the lead from the heat pad to the switch to become warm as this is part of the heated protection circuit extended to the switch. Electrical requirements Check that the voltage on the rating label of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance, the plug should be removed and the appropriate one fitted. WARNING: The plug removed from the mains lead, if severed, must be destroyed as a plug with bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require changing, a 3 amp BS1362 fuse must be fitted. This appliance does not need to be earthed. It is a double insulated product. Action in case of activation In the event of the OVERHEAT SYSTEM operating, the heat pad will cease to function and must be returned to the service department address given in this leaflet. WARNING: No attempt should be made to repair the heat pad or have it repaired locally and the switch supplied must never be replaced other than by the manufacturers since the specialised components are not generally available. The fact that this heat pad incorporates the overheat system does not absolve the user from observing these instructions. Before use Before using this appliance ensure that the voltage indicated on the product corresponds with the mains voltage in your home. If you are in any doubt about your supply, ask your electrical dealer or local electricity company. 3 Switch 9 Rev 1 30/9/04 2:46 PM Page 4 Switch control Features / ¤ < > fi / Illuminated heat setting light (To identify heat levels in the dark) ¤ Heat levels 3 & 4 < Heat level 1 & 2 > Braille markings (located on the back of the switch) fi Off position How to use 1 Apply the pad on the area to be treated. 2 Select the heat setting as required. Braille markings · Braille markings are located on the back of the switch to help identify the direction of the heat level in the dark, or if visually impaired. · The highest heat level high level is identified by 3 raised nodules mid level by 2 raised nodules low level by 1 raised nodule. Heat levels 1 and 2 Will provide continuous steady warmth and can be used for longer periods of time up to a maximum of 3 hours. Heat levels 3 and 4 Will provide a higher level of heat and should be used for a shorter period of time. To avoid excessive heat exposure the heat pad will automatically reduce the temperature to less than 50°C after 90 minutes and will switch off completely after 3 hours. WARNING: This safety device prevents over exposure to excessive temperatures which can result in skin damage. 4 Switch 9 Rev 1 30/9/04 2:46 PM Page 5 Washing instructions 1 Remove fleece cover and wash on a wool programme at 40°C. 3 Ensure cover is completely dry before using. WARNING: The pad must never be washed but can be wiped carefully with a damp cloth. Helpline Should you need any advice on using the product, please contact our helpline, 8:30 - 5:00 Mon - Thurs 8:30 - 4:00 Fri Tel: 08700 602616 Servicing · The pad should be serviced every 2 years. Pack and send carriage paid to the Service department (see address below). · A standard service charge (inclusive of packing and return carriage) is made for routine inspection where no repair is found to be necessary. · If the pad fails to operate, check the following before retuning: 1 Ensure that the plug and socket have not become disconnected. 2 Check that the supply plug is correctly connected to the flex. 3 Check the supply fuse and the 3 amp plug fuse if applicable. [. . . ] This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. · This guarantee is valid in the UK and Ireland only. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 12 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. [. . . ]