User manual MORPHY RICHARDS IB86003

[. . . ] · Close supervision is necessary when any appliance is used near children. Never allow a child to operate this appliance. · Children are vulnerable in the kitchen particularly when unsupervised and if appliances are being used or cooking is being carried out. · Teach children to be aware of dangers in the kitchen, warn them of the dangers of reaching up to areas where they cannot see properly or should not be reaching. Children Mains lead The socket should always be off before plugging or unplugging from the socket. [. . . ] Acrilan Courtelle, Orlon Triacetates, e. g. If moisture required use damp cloth (Not Acetate) Dry and spray Dry ironing Wool, polyester mixtures e. g. Polyester/Cotton Cotton, linen Rayon, Rayon mixtures, e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc Steam/spray/shot of steam Ironing With water in tank Without water in tank 3 STEAM IRON 3 31/5/02, 11:47 AM Components of your iron Before use Note : The steam facility should only be used on garments which are suitable for ironing at the 3 dot setting. Textiles and clothes are supposed to carry ironing instructions. If they don't you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Cordless (certain models only) Filling 1 Make sure that the iron is not plugged in and then set the variable steam control to the lowest position before filling the iron with water. 2 Fill the water through the filling hole into the water tank , using the beaker provided. Shot of steam button Spray button Variable steam control Filling hole Spray nozzle Soleplate Water tank Temperature control dial with indicator Temperature indicator light Iron Base stand (Certain models only) Power unit Iron stand 3 position base switch = Cordless ironing = Storage/lock position = Corded ironing In hard water areas the use of distilled or demineralised water is recommended. Never use battery topping-up fluid or water containing any substances like starch or sugar, or defrosted water from a refrigerator. 4 STEAM IRON 4 31/5/02, 11:47 AM Corded ironing 1 Set the 3 positions base switch to the corded position . 2 Take the iron (with power unit) from the stand. 3 Either place the iron (with power unit) on its heel rest or on the stand when you interrupt ironing. Temperature control Plug in the iron and switch on. Set the temperature control dial to the temperature required, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. Cordless ironing 1 Set the 3 positions base switch to the cordless position . 2 Take the iron (without power unit) from the stand. 3 Always place the iron on the stand when you interrupt ironing. 4 For optimal ironing performance the iron should be replaced on the base stand to heat up to the correct temperature. As soon as the set temperature is regained the light will go out. 5 When cordless steam-ironing for a considerable time, when applying shots of steam the soleplate may cool down more quickly. We recommend to always use the corded mode if you intend to steam iron for a considerable time. 6 When storing your iron on the stand ensure the iron is left in the storage/ lock position . Your Goblin iron is fitted with an indicator which will go on and off while you light are ironing. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. It is always a good idea to begin with `cool' fabrics and work up to higher settings. [. . . ] Disconnect the iron from the mains outlet and hold the iron horizontally over a sink. Pull and hold the variable steam control to the self cleaning position. Self cleaning Self cleaning Important : The flex can be damaged if wound too tightly around the iron after use. Make a loose loop with the flex and wrap it around the iron or stand. The iron must be cool before winding the flex and storing on its heel. Steam and boiling water will emit from the holes on the soleplate washing away scale and mineral deposits in the steam chamber. [. . . ]