User manual MORPHY RICHARDS JET STREAM

[. . . ] 42277 rev6:42288 rev1 08/04/2009 10:24 Page 1 Jet Steam & Jet Stream Please read and keep these instructions ironing system Getting the best from your new ironing system. . . . Safety first Caution must be used when handling this appliance as it does get very hot. Always switch off the unit and allow to cool before cleaning or storing. Water tank (certain models are illuminated) The water tank can be removed and re-filled at any time during ironing. Certain Morphy Richards steam generators have an illuminated water tank. The changing colours enhance the mood for ironing by creating a colourful atmosphere to help you glide through your washing basket. [. . . ] If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. 4 UK Helpline 0844 871 0953 Replacement Parts 0844 873 0719 Ireland Helpline 1800 409 119 42277 rev6:42288 rev1 08/04/2009 10:24 Page 5 FILLING 1 Place the steam generator on a stable ironing board or table, with the iron resting on its stand. Release the detachable water tank by sliding outwards A. Remove the anti-scale cartridge by pulling upwards B. Fill the tank to the `fill to here' line with clean tap water C. IN HARD WATER AREAS, THE USE OF DISTILLED OR DEMINERALISED WATER IS RECOMMENDED. WARNING: Never use battery topping up fluid or water containing any substances like starch or sugar, or defrosted water from a refrigerator. 5 Re-install the anti-scale cartridge and re-position the water tank on the base unit and push securely into place. Always pour out any remaining water after use. 3 2 3 4 Connect the appliance to a suitable mains outlet, and switch on the socket. All 5 red lights will flash once only and a beep will be heard. Press the power on switch , and the unit will turn on, it will default to Max steam, and the "on" light will flash red whilst heating up. When ready for use, the light will turn green. Press the power switch again to scroll through steam settings to the "no steam" position (no steam lights illuminated). Press the power switch again to go to the maximum steam position. Turn the temperature dial on the iron in a clockwise direction, select dot-1, dot-2 or dot-3 according to the recommendation of the garment label. The iron's temperature indicator light > goes off when the required temperature is reached. Depress the steam button / for 1 minute to clear the system of air (first time use only) which will be accompanied by a clicking noise which is quite normal. Begin first time ironing with an old towel. Note: If you press the steam button before the steam generator reaches its required temperature, a warning double bleep will sound. It takes about 1 minute to reach the required temperature. Press the power button , to choose the steam level from `steam off', `low steam', `medium steam' and `maximum steam'. A 4 B 5 6 C 7 6 Re-filling `in use' 1 When the water level becomes low, the pump begins to emit a clicking noise. This is due to air being pumped instead of water and is quite normal. Refilling can be done whilst the appliance is in operation. [. . . ] 1 Slide out the water tank and remove the anti-scale cartridge K. To clean the exterior Allow the steam generator to cool and wipe over with a damp cloth and mild detergent, then wipe with a dry cloth. L For details of other Morphy Replacement Parts 0870 our website: UK Helpline 0870 060 2614Richards products, please see157 6645 Ireland Helpline 1800 409119 7 42277 rev6:42288 rev1 08/04/2009 10:24 Page 8 YOUR TWO YEAR GUARANTEE It is important to retain the retailer's receipt as proof of purchase. Staple your receipt to this back cover for future reference. Please quote the following information if the product develops a fault. These numbers can be found on the base of the product. [. . . ]