User manual MORPHY RICHARDS POLAR FLEECE MATTRESS TOPPER 75270

[. . . ] Do not dry clean the blanket, follow washing instructions on the label attached to the blanket and the details that relate to your blanket. · Personal safety · WARNING: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Do not use with a helpless person, an infant or a person insensitive to heat. Young children should be instructed on how to operate the controls safely, and heat settings should be controlled by a parent or guardian. [. . . ] It is normal for the lead from the blanket to the switch to become warm as this is part of the heater protection circuit extended to the switch. In the event of the OVERHEAT SYSTEM operating, the blanket will cease to function. WARNING: No attempt should be made to repair the blanket or have it repaired locally and the switch supplied must never be replaced as the specialised components are not generally available. The fact that this blanket incorporates the overheat system does not absolve the user from observing these instructions. Dual control models On double dual models, users are able to control their own side of the bed with individual controls, tailoring independent temperatures to independent needs. Each side of the blanket has a completely separate element and each is supplied with it's own independent mains lead. Do not connect both flexible cords to one 13amp plug. The two leads should preferably be plugged into individual sockets. However, if only one socket is accessible, then a multi adaptor should be used. WARNING: If you are unsure about electrical connections, please contact a qualified engineer. It is quite normal for the switch to become warm, as the components encased are part of the protection circuit. 4 UK Helpline 0844 871 0948 Ireland Helpline 1800 409 119 75270 rev2 22/4/08 10:40 Page 5 Mattress covers with elasticated skirt. · NOTE: This product can be used with any type of bedding, including waterproof bed protectors. Place the mattress cover directly on the mattress. Make sure the control switch end is at the head of the bed, with the connector facing upwards A. Fit the shaped corners to the mattress and turn the elasticated edges of the skirt under the mattress. Ensure all creases are smoothed out and the skirt fits tightly round the sides of the mattress. · · · A 5 75270 rev2 22/4/08 10:40 Page 6 HOW TO USE 1 Ensure the blanket is fitted to 2 Plug the power lead into the the bed correctly, see diagram A. closest socket, using an extension lead, if needed, to ensure that the lead is not stretched. · · WASHING INSTRUCTIONS WARNING: Do NOT dry clean Do NOT iron WARNING: Before washing, ensure that you detach all the controls from the blanket. · Only use a washing machine with a drum large enough to take the blanket without forcing it in. Measure the blanket so it can be stretched back to it's original size whilst wet. NOTE: Please ensure washable models are fully dry before use. Preheating the bed Move the heat setting on the control switch to heat level 2 or 3, depending on the level of the heat required. Allow approximately 60-90 minutes for the blanket to heat the bed thoroughly, although this time may vary depending on the room temperature and type of bedding used. · All night use NOTE: Blankets are perfectly safe to be used all night. However, we recommend using the heat setting below. · · Move the heat setting on the control switch to heat level 1. [. . . ] If the fault develops after 28 days and within 36 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. You may be asked to return a copy of proof of purchase. Subject to the exclusions set out below (see Exclusions), the faulty appliance will then be replaced and dispatched usually within 28 working days of receipt. If, for any reason, this item is replaced during the 3 year guarantee period, the guarantee on the new item will be calculated from the original purchase date. Therefore, it is vital to retain your original till receipt or invoice to indicate the date of initial purchase. [. . . ]