User manual MORPHY RICHARDS SPILLMASTER 70330

[. . . ] Do not place in or near heating appliances to dry. For replacement parts, help with using your Morphy Richards product, problems and lots more, contact us by phone or through our website. UK Helpline: 0844 871 0949 Replacement Parts: 0844 873 0715 Ireland Helpline: 1800 409 119 VC70330 MUK Rev 1 www. morphyrichards. com 70330 rev1 19/6/08 10:15 Page 2 IMPORTANT SAFETY INSTRUCTIONS The use of any electrical appliance or attachment requires the following common sense safety rules. Primarily there is danger of injury or death and secondly the danger of damage to the appliance. Please read these instructions before using the attachment. Product safety · · · Do not modify the product in any way. [. . . ] It is not recommended to use any extension tubes when using the SpillMaster. Ensure only the nozzle touches the floor, so the water tank is not dragged through the liquid spill. Backward strokes are more effective on deeper carpets. 4 UK Helpline 0844 871 0949 Replacement Parts 0844 873 0715 Ireland Helpline 1800 409 119 70330 rev1 19/6/08 10:15 Page 5 SAFETY FEATURES As well as the hose filter, there are three other main safety features F which will cut off suction to the SpillMaster in the event of improper use: If the SpillMaster is tilted backwards, a slug in the nozzle suction chamber will slide backwards, blocking the suction to the hose G. If the SpillMaster is tilted sidewards, a slug in the suction chamber connecting to the liquid tank will slide upwards, blocking the suction in the unit G. F Before safety features activate Safety features activated G EMPTYING THE SPILLMASTER Ensure the vacuum cleaner power is switched off. If the SpillMaster is overfilled with liquid, a float in the liquid tank will rise upwards, blocking the suction in the unit. If any of the above occurs, turn off your vacuum cleaner immediately, empty the tank, reassemble the SpillMaster and resume use as described in `Using the SpillMaster' section. Remove the vacuum hose from the SpillMaster. Take the SpillMaster to a sink or drain to empty. Press down on the tank release button with one finger H. With the other hand, rotate the handle section anti-clockwise as far as possible H. Pull upwards to separate the unit into it's two parts. Empty the contents of the reservoir by tipping it upside down over a sink or drain I. H I www. morphyrichards. com 5 70330 rev1 19/6/08 10:15 Page 6 J CLEANING THE SPILLMASTER It is recommended that the SpillMaster is regularly cleaned to prevent any build up of residue. Remove the filter by squeezing the two white areas with a finger and thumb and pull the white tab until the filter is clear of the product J. Separate the SpillMaster into it's two parts as described in the `Emptying the SpillMaster' section. Empty the contents of the base unit over a sink and then rinse the reservoir with lukewarm water to remove any residue. Leave to dry upside down for at least 24 hours or until completely dry K. · After use, empty the contents of the water tank, clean and dry the product fully. Regularly check that the filter is not blocked, dirty or damp. If the filter becomes dirty, rinse in lukewarm water and leave to dry fully before re-use. If the filter becomes damaged, it must be replaced. Call our helpline for replacement parts. When carrying the SpillMaster to the sink, ensure it is kept horizontal to prevent any spillage. · · · PRODUCT STORAGE · · · When finished, do not store near any heat sources. Only store when dry. HINTS & TIPS (also see `Safety Features') · The SpillMaster can be used on all floor types but must only be used for liquid spills. [. . . ] The appliance has been used for hire purposes or non domestic use. Morphy Richards are not liable to carry out any type of servicing work under the guarantee. The guarantee excludes consumables such as filters. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. [. . . ]