User manual MORPHY RICHARDS TURBOSTEAM IRON

[. . . ] Never yank the cord to disconnect from the socket, instead, grasp the plug and pull to disconnect. Do not allow the cord to touch hot surfaces. Let the iron cool completely before putting away. Loop the cord loosely around the iron before storing. [. . . ] When ironing with the steam facility at the 2 dot setting, the steam output should be set at the lower end of the steam range (see `Variable steam' section). Textiles and clothes are supposed to carry ironing instructions. If they don't, you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. ¤ < > fi , fl · 400 350 300 , , 1 FILLING A Make sure that the iron is not plugged in and then set the variable steam control < to the `0' position before filling the iron with water. Remove the fill cap and pour water through the filling hole > into the water tank ·, using the beaker provided. One beaker full of water fills the tank (400ml) A. In hard water areas, the use of distilled or demineralised water is recommended. Never use battery topping-up fluid or water containing any substances like starch or sugar, or defrosted water from a refrigerator. 3 Always pour out the remaining water after use. WARNING: When filling your iron with tap water, always use the beaker provided. Never fill directly under the tap. A COMPONENTS OF YOUR IRON / Shot of steam button ¤ Spray button < Variable steam control > Filling hole with cap fi Spray nozzle fl Soleplate Temperature control dial · Water tank , Temperature indicator light , , Filling beaker 2 4 UK Helpline 0844 871 0953 Replacement Parts 0844 873 0719 Ireland Helpline 1800 409 119 40513 rev1:RN40513 MUK Rev1 18/02/2009 11:16 Page 5 Temperature control B Plug in the iron and switch on. Set the temperature control dial to the temperature required B, but don't start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. Your Morphy Richards iron is fitted with a temperature indicator light , which will go on and off while you are ironing. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. It is always a good idea to begin with `cool' fabrics and work up to higher settings. An iron heats up quicker than it cools down so you'll save time and electricity. Spray C Press the spray button ¤ and aim the spray of water at stubborn creases. You can do this whilst dry ironing, providing there is water in the tank. When using the water spray, it may be necessary to push the button a few times to get the spray pump primed. B Variable steam Fill the iron with water as described in `Filling', and insert the plug into the electrical socket. The steam output can be varied from low to high by rotating the variable steam control D. C FEATURES OF YOUR IRON Temperature indicator light The indicator light shows that the iron is warming up. When the required temperature is reached, the light will go out and will cycle on-off during operation. The steam facility should only be D used on garments which are suitable for ironing at 2 and 3 dot settings. Shot of steam E (certain models only) Press the shot of steam button / to obtain a burst of extra steam for ironing out creases in heavy material such as denim etc. The shot of steam can be used whilst dry ironing, providing there is water in the tank, and the temperature control is set within the steam range. [. . . ] This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. This guarantee is valid in the UK and Ireland only. 5 6 7 · EXCLUSIONS Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturer's recommendations, or where the fault has been caused by power surges or damage caused in transit. The appliance has been used on a voltage supply other than that stamped on the products. Repairs have been attempted by persons other than our service staff (or authorised dealer). [. . . ]