User manual MOTOROLA HEADSET H300

[. . . ] If you need more help, contact us at 1-877-MOTOBLU or visit us at www. hellomoto. com/bluetooth and click Support. Charge your headset's battery for 2 hours: Before you can use your headset, you must pair (link) it with your phone. Call Button Blue Indicator Light With the headset power off, press and hold the Call button for 6 to 10 seconds until the blue indicator light turns on and remains steadily lit. Note: The blue light will flash as you press and hold the Call button. Continue holding down the Call button until the blue light is steadily lit. [. . . ] Continue holding down the Call button until the blue light is steadily lit. Note: If you let go of the Call button before the blue light is on and steady, ensure that your headset is off before trying again. Note: To turn off headset, see "Turning Headset On/Off" on the reverse side of this guide. H3 Bluetooth® Handsfree Headset Get Connected in 4 Quick Steps 1 - CHARGE YOUR HEADSET 2 - PUT HEADSET IN PAIR MODE 3 - PAIR PHONE WITH HEADSET 4 - TEST AND USE Take a moment before you get started to familiarize yourself with your new H3 Handsfree Headset. Earhook Call Button Volume Buttons Blue Indicator Light 1 Plug the Motorola charger into the end of the headset. The blue indicator light turns on when the battery is charging. It may take up to 1 minute for the light to turn on. When the headset's battery is fully charged (about 2 hours), the blue indicator light turns off. Microphone 2 Unplug the charger from the headset. Note: Headset is not functional while charging. Motorola, Inc. Consumer Advocacy Office 1307 East Algonquin Road Schaumburg, IL 60196 www. hellomoto. com 1-877-MOTOBLU 1-888-390-6456 (TTY/TDD United States for hearing impaired) Guide Number: 6809498A97-O 3 TURN ON BLUETOOTH ON YOUR PHONE AND PAIR WITH HEADSET TURN ON BLUETOOTH ON YOUR PHONE AND PAIR WITH HEADSET Continued 4 TEST AND USE USING YOUR H3 See Features and Functions Guide on the reverse side of this guide for information on using your H3. Your phone's Bluetooth feature is off by default. To turn your headset off, press and hold the Call button until the indicator light flashes rapidly and then turns off. WEARING THE HEADSET 1 Open the earhook. 3 Press the headset to your ear. CHANGING FOR USE ON OTHER EAR You can wear your H3 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear: CHANGING VOLUME BUTTON ORIENTATION If you change your headset to wear on the other ear, you can also change the orientation of the volume buttons. 1 Open the earhook 90 degrees from the headset. 1 Turn the headset power off. 2 Press the Call button along with the 1 Open Earhook 2 Pull Earhook Up 2 Gently lift and pull the IMPORTANT: Be sure to first follow the Quick Start Guide on the reverse side of this guide to complete initial setup of your H3. Call Button top of the earhook up and off the upper hinge pin. Then, pull it away to remove it. Volume button you want to assign as "volume up" button until the indicator light flashes twice. Call Button Volume Buttons 3 Flip the headset over. 4 Hook the bottom of 3 4 the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin. Hinge Pin MAKING CALLS Function Make a voice dial call End a call Receive a call Reject a call Redial last call Answer a second incoming call Action Tap the Call button and speak the name after the tone Tap the Call button Tap the Call button Press and hold the Call button until you hear a beep Press and hold the Call button until you hear a beep Press and hold the Call button (places first call on hold) MAKING CALLS CONTINUED Function Toggle between two active calls Join a 3-way call Put an active call on hold or resume a call on hold Transfer a call from the phone to the headset Disable or enable the indicator light Mute or unmute a call Action Press and hold the Call button Press and hold both Volume buttons Press and hold the Call button until you hear a beep Tap the Call button Press and hold both Volume buttons for 3 to 4 seconds Tap both Volume buttons INDICATOR LIGHTS The indicator light provides information about your headset status. [. . . ] Then, pull it away to remove it. Volume button you want to assign as "volume up" button until the indicator light flashes twice. Call Button Volume Buttons 3 Flip the headset over. 4 Hook the bottom of 3 4 the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin. Hinge Pin MAKING CALLS Function Make a voice dial call End a call Receive a call Reject a call Redial last call Answer a second incoming call Action Tap the Call button and speak the name after the tone Tap the Call button Tap the Call button Press and hold the Call button until you hear a beep Press and hold the Call button until you hear a beep Press and hold the Call button (places first call on hold) MAKING CALLS CONTINUED Function Toggle between two active calls Join a 3-way call Put an active call on hold or resume a call on hold Transfer a call from the phone to the headset Disable or enable the indicator light Mute or unmute a call Action Press and hold the Call button Press and hold both Volume buttons Press and hold the Call button until you hear a beep Tap the Call button Press and hold both Volume buttons for 3 to 4 seconds Tap both Volume buttons INDICATOR LIGHTS The indicator light provides information about your headset status. [. . . ]