User manual MOTOROLA SBV5220 SURFBOARD DIGITAL VOICE MODEM

[. . . ] User Guide SBV5220 VoIP Cable Modem Introduction Installation Troubleshooting Glossary License Safety and Regulatory Information WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE UNIT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ON THE UNIT. CAUTION: THIS PRODUCT WAS QUALIFIED UNDER TEST CONDITIONS THAT INCLUDED THE USE OF THE SUPPLIED CABLES BETWEEN SYSTEMS COMPONENTS. [. . . ] If you still cannot find the correct driver file, click Cancel to cancel the installation and perform the procedure for "Removing the USB Driver from Windows 98 Second Edition or Windows Me" on page 42. Then repeat this procedure. Although your Motorola VoIP cable modem model number may be different than in the images in this guide, the procedure is the same. SBV5220 VoIP Cable Modem User Guide 15 Introduction Installation Troubleshooting Glossary License 9 After the window shown under step 8 is displayed, click Next. If a window with the message Copying Files. . . displays and asks for your CD-ROM drive, type your CD-ROM drive letter (for example, "D:") and click OK. If an Insert Disk window similar to the following is displayed, Windows system files are needed to complete the installation. To install the files, insert your Windows 98 Second Edition CD-ROM in the CD-ROM drive and click OK. After all the necessary files are loaded, the following window is displayed confirming a successful installation: 10 Click Finish. The Systems Settings Change window is displayed: 11 Click Yes to restart your computer. When you finish setting up the USB driver, you can continue with "Configuring TCP/IP in Windows 98, Windows 98 Second Edition, or Windows Me" on page 22. If you have difficulties setting up the USB driver, perform "Removing the USB Driver from Windows 98 Second Edition or Windows Me" on page 42 and repeat this procedure. If that does not correct your problem, see the Regulatory, Safety, Software License, and Warranty Information card provided with your Motorola VoIP cable modem for information about obtaining warranty service. SBV5220 VoIP Cable Modem User Guide 16 Introduction Installation Troubleshooting Glossary License Setting Up a USB Driver in Windows 2000 1 2 Insert the SBV5220 VoIP Cable Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the Motorola VoIP cable modem to the PC. Connect the Motorola VoIP cable modem to your computer with a USB cable. For further instructions, see "Cabling and Startup for a Single User" on page 10. A few seconds after you complete the USB connection, the Found New Hardware Wizard window is displayed: 3 Click Next. The following window is displayed: Although your Motorola VoIP cable modem model number may be different than in the images in this guide, the procedure is the same. Be sure "Search for a suitable driver for my device" is selected. SBV5220 VoIP Cable Modem User Guide 17 Introduction Installation Troubleshooting Glossary License 4 Click Next. The following window is displayed: Be sure "CD-ROM drives" is the only box selected. 5 Click Next. The following window is displayed: 6 Click Next. If the Insert Disk window is displayed, be sure the SBV5220 VoIP Cable Modem CD-ROM is in the CD-ROM drive and follow steps 7 to 11. Otherwise, if the Completing the Found New Hardware window is displayed, you can skip to step 12. SBV5220 VoIP Cable Modem User Guide 18 Introduction Installation Troubleshooting Glossary License 7 On the Insert Disk window, click OK. The Files Needed window is displayed: 8 9 If necessary, select your CD-ROM drive in the "Copy files from" list. Click Browse. 10 Double-click the NetMotCM. sys file in the CD-ROM root directory. The Files Needed window is displayed: 11 Click OK. [. . . ] Motorola and its 3rd party licensors retain the ownership of the Software. You may: USE the Software only in connection with the operation of the Product. TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only if the person agrees to accept all of the terms of this License. If you transfer the Software, you must at the same time transfer the Product and all copies of the Software (if applicable) to the same person or destroy any copies not transferred. [. . . ]