User manual MOTOROLA SURFBOARD CABLE MODEM SB4220

[. . . ] Title SURFboard Cable Modem SB4220 Series User Guide Click your selection: Introduction Introduces your SURFboard cable modem and the controls on the Top and Front Panel and Rear Panel. Before You Begin Lists the items needed to install your SURFboard cable modem and describes Precautions, Signing Up for Service, and Computer System Requirements. Installation and Configuration Overview Provides an overview and links to cable and configure your SURFboard cable modem, including Setting Up a USB Driver. Troubleshooting Provides suggestions to fix common problems. Contact Us Provides contact information. Frequently Asked Questions Provides answers to common questions about the SURFboard cable modem. Next page SURFboard Cable Modem R WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS DEVICE TO RAIN OR MOISTURE. THE DEVICE SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE DEVICE. CAUTION: TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES. [. . . ] If there is more than one TCP/IP entry, choose the one for the Ethernet card or USB port connected to the cable modem. 11 Click Properties. 13 Click Obtain an IP address automatically. 14 Click OK to accept the TCP/IP settings. 15 Click OK to close the Network window. 16 Click OK when prompted to restart your computer and click OK again. When you complete TCP/IP configuration, go to "Verifying the IP Address in Windows 95, 98, or Me" on page 30. Home Print Exit X 25 SURFboard Cable Modem SB4220 Series User Guide Introduction Before You Begin Installation & Configuration Troubleshooting FAQ Glossary License Configuring TCP/IP in Windows 2000 or XP The following instructions are for Windows 2000 or XP. For Windows 95, 98, or Me, see "Configuring TCP/IP in Windows 95, 98, or Me" on page 23. For a Macintosh or UNIX system, refer to your user guide. 1 2 3 4 On the Windows Desktop, click Start. Select Settings and then Control Panel from the pop-up menus. Double-click the Network and Dial-up Connections icon on the Control Panel window. On the Network and Dial-up Connections window, click Local Area Connection number. The value of number varies from system to system. The Local Area Connection number Status window is displayed. Home Print Exit X 26 SURFboard Cable Modem SB4220 Series User Guide Introduction Before You Begin Installation & Configuration Troubleshooting FAQ Glossary License Configuring TCP/IP in Windows 2000 or XP, continued 5 6 Click Properties. Information similar to the lower window is displayed. If Internet Protocol (TCP/IP) is in the list of components, TCP/IP is installed. If Internet Protocol (TCP/IP) is not in the list, click Install. The Select Network Component Type window is displayed. Continue with step 7. Home Print Exit X 27 SURFboard Cable Modem SB4220 Series User Guide Introduction Before You Begin Installation & Configuration Troubleshooting FAQ Glossary License Configuring TCP/IP in Windows 2000 or XP, continued 7 8 9 Click Protocol on the Select Network Component Type window and click Add. The Select Network Protocol window is displayed. Click Internet Protocol (TCP/IP) in the Network Protocol section on the Select Network Protocol window. The Local Area Connection number Properties window is re-displayed. Home Print Exit X 28 SURFboard Cable Modem SB4220 Series User Guide Introduction Before You Begin Installation & Configuration Troubleshooting FAQ Glossary License Configuring TCP/IP in Windows 2000 or XP, continued 10 On the Local Area Connection number Properties window, be sure the box next to Internet Protocol (TCP/IP) is checked. 11 Click Properties. The Internet Protocol (TCP/IP) Properties window is displayed as shown at bottom left. 12 Be sure Obtain IP address automatically and Obtain DNS server address automatically are selected. 13 Click OK to accept the TCP/IP settings. 14 Click OK to close the Local Area Connection number Properties window. [. . . ] Software provided by third parties may be subject to separate end-user license agreements from the manufacturers of such Software. Motorola licenses the Software to the original customer and to any subsequent licensee for personal use only on the terms of this License. Motorola and its 3rd party licensors retain the ownership of the Software. Home Print Exit X 59 SURFboard Cable Modem SB4220 Series User Guide You may: USE the Software only in connection with the operation of the Product. TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only if the person agrees to accept all of the terms of this License. [. . . ]