User manual MOTOROLA UNIVERSAL REMOTE CONTROL DRC400

[. . . ] DRC-400/425 UNIVERSAL REMOTE CONTROL Press POWER once to turn on or off the selected home entertainment component. Press HELP once to display the help screen. Press MUTE once to turn sound off or on. Use PAGE s (or PAGE t) to page up (or down) through menu screens and the program guide. [. . . ] If you perform this procedure correctly, the AUX light will blink three times. NOTE: If you enter an invalid code, the AUX light will turn off. In that case, repeat steps 2 through 5 with a valid code. SEARCHING FOR YOUR CODE If your TV, VCR, Cable Converter or Auxiliary Component does not respond to the DRC after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, after trying all of the codes for your TV, you still cannot get the DRC to operate your TV, then: 1. On the DRC, press and hold TV (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release TV and wait until it's lit continuously. Press the (UP) cursor key once to start the search mode. NOTE: In the search mode, the DRC will send IR codes from its library to the selected component, starting with the most popular codes first. When the component responds to a subsequent key command (e. g. , POWER), the correct device code will be found. CHECKING THE CODES If you have set up the DRC using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment. Perform the following procedure after you have set up your components to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV: 1. On the DRC, press and hold TV (at least 6 seconds) until you see the mode light sequence start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and will repeat twice. During the sequence, release the TV key and wait until it stays lit continually. To view the code for the first digit, press and release 1. Count the number of TV key blinks (e. g. , 3 blinks = 3) and write down the number in the leftmost box below. NOTE: The mode key will not blink if the code digit is a "0". CHANGING VOLUME LOCK Your new DRC is set to control volume of a component through its associated mode (i. e. , through the cable in the Cable mode, through the TV in the TV mode, and through the auxiliary device in the Aux. If your TV is not remote controllable, or if you would like the volume to be controlled by a different component, you can change the Volume Lock setting to control a volume through a non-associated mode (e. g. , through the cable in the TV mode). Changing the Volume Lock setting to the Cable or TV mode will change the volume control for all modes except Aux. , which will continue to control its own volume. If you change the Volume Lock setting to the Aux. mode, all modes (i. e. , Aux. , Cable, and TV) will be controlled by the Aux. mode. NOTE: The volume controls will not operate if Volume Lock is set to VCR mode. To change the Volume Lock setting to the AUX mode: 1. On the DRC, press and hold AUX (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release AUX and wait until it's lit continuously. The AUX key light will blink three times, indicating volume has been locked to the AUX mode. [. . . ] Finish writing down the code in the boxes above. To check for the codes of your other components, repeat steps 1 through 5, only substitute the appropriate device key (i. e. , VCR, CABLE, or AUX) for the component you are checking. Write down the codes in the boxes below. VCR 5. Aim the DRC at your Cable Converter or DBS Receiver and and press POWER once. Your Cable Converter or DBS receiver should turn off. If it does not respond, repeat steps 2-4, trying each code listed for your brand until you find the one that operates your Cable Converter or DBS Receiver. [. . . ]