User manual MOTOROLA VT1000 VOICE TERMINAL

[. . . ] User Guide VT1000 Series Voice Terminal Important This guide contains information related to product warranty, regulatory matters, and software licenses. License Safety and Regulatory Information WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS DEVICE TO RAIN OR MOISTURE. THE DEVICE SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE DEVICE. CAUTION: TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES. TO PREVENT ELECTRICAL SHOCK, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. [. . . ] Type the Static IP Address and IP addresses for the Subnet Mask, Default Gateway they provide. Specify Static IP Address Enable PPPoE If you have a DSL modem and no router, enable PPPoE and type the Service Name, User Name, and Password provided by your DSL provider. 19 Specify DNS Servers Enables you to specify Domain Name System (DNS) servers, if necessary: · If Obtain IP Address Dynamically or Enable PPPoE are selected, Specify DNS Servers is off by default. If required by your broadband provider only, select Specify DNS Servers and type the DNS server IP addresses provided by your broadband provider. · If Specify Static IP Address is selected, Specify DNS Servers is selected by default. Because no DNS server is automatically assigned, you need to type the DNS server IP addresses provided by your broadband provider. 4 Verify that all fields are correctly filled in and click Save Changes. The message This will require a reboot of the unit. You cannot display the configuration pages while the Motorola voice terminal starts up. After the Motorola voice terminal restarts, click the Web browser Refresh button to display the configuration pages. Pick up the telephone hand set and listen for a dial tone. If you hear a dial tone, you can now place a phone call as you would with any telephone. 5 6 20 VT1000 Series Voice Terminal User Guide If you cannot a hear a dial tone, try the following: · · · · Check that all cabling is correctly connected as described in "Installation" on page 11. Repeat this Basic Configuration procedure. Be sure you enter the correct information for your service. Refer to "Troubleshooting" on page 26. Contact your VoIP provider. 21 Advanced Configuration Do not change these settings unless you have the necessary expertise and the need to do so. Field or Button Enable DHCP/NAT on LAN Port Virtual Servers Description If this is enabled, the Motorola voice terminal automatically distributes an IP address to a computer connected to its PC port. Configures logical data ports for applications requiring multiple data ports. Because NAT assumes that data sent through one port will return to the same port, you may need to configure virtual servers to run certain applications: · · IP is the IP address of the computer connected to the Motorola voice terminal Port sets the port to open. The ports assigned to Motorola voice terminal voice functions are displayed. If you forward any of these ports, you may disrupt your voice service. The ports shown in the illustration are examples only. Transport sets the protocol -- Disabled, TCP, IP, or UDP. · 22 VT1000 Series Voice Terminal User Guide Field or Button Enable DMZ Description Select Enable DMZ to enable the computer having the DMZ Host Address to be the de-militarized zone (DMZ). Use this setting with extreme caution because a DMZ host can be accessed by any computer on the Internet and is completely open to Internet hackers. DMZ Host Address Type the last octet of the IP address of the device you want to designate as the DMZ host. Host Name MAC Address Override Type the host name, if required by your broadband provider. If your broadband provider associates a particular service to a specific device, such as your computer, type its MAC address here to use instead of the Motorola voice terminal MAC address. [. . . ] (4) Remove, alter or cause not to be displayed, any copyright notices or startup message contained in the Software programs or documentation. (5) Export the Software or the Product components in violation of any United States export laws. The Product is not designed or intended for use in on-line control of aircraft, air traffic, aircraft navigation or aircraft communications; or in design, construction, operation or maintenance of any nuclear facility. MOTOROLA AND ITS 3rd PARTY LICENSORS DISCLAIM ANY EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR SUCH USES. [. . . ]