User manual MOULINEX VITA COMPACT FOOD PROCESSOR

[. . . ] MOULI GB 12/10/06 15:33 Page 1 1 MOULI GB 12/10/06 15:33 Page 2 b1 d1 d2 c A/D b2 h1 b3 h2 C/H E G e f a1 a2 j1 h3 j2 g1 g2 i1 i2 k1 g3 i3 i4 g4 k2 2 MOULI GB 12/10/06 15:33 Page 3 l m7 m6 m4-1 m4-2 ma m4-3 m4-4 m5 m4 m3 m2 m n m7 m6 m4-1 mb m4-2 m1 o1 o2 p1 p2 m5 m4 m3 m2 r m1 q5 q4 q m5 q3 q2 q1 q3-1 q3-2 s 3 MOULI GB 12/10/06 15:33 Page 4 3 1 2 4 fig. 1a fig. 1b fig. 1c 2 1 3 fig. 2a fig. 2b fig. 2c 5 4 3 2 6 1 fig. 3 5 4 2 3 6 1 fig. 4 5 4 2 3 6 fig. 5 1 3 4 2 5 4 3 3 5 2 1 fig. 7 fig. 8 4 5 6 1 2 1 fig. 6 4 MOULI GB 12/10/06 15:33 Page 5 5 4 3 2 6 1 fig. 9 fig. 10a fig. 10b 2 2 1 1 fig. 10c fig. 10d fig. 10e fig. 10f fig. 10g fig. 11a 5 4 2 3 1 fig. 11b fig. 11c 5 MOULI GB 12/10/06 15:33 Page 6 Thank your for choosing a Moulinex product exclusively designed for food preparation. Safety recommendations - Read the instructions for use carefully before using your appliance for the first time: Moulinex does not accept responsibility for use that does not comply with the instructions. - Do not leave the appliance running unsupervised, especially when young children or disabled people are present. - Check that the power supply voltage corresponds to that shown on the appliance (alternating current). - Any error in connection will cancel the guarantee. [. . . ] - Plug the appliance in. 10c : Assembling the mincer head (ma) or (mb) - Take the body (m1) by the feed tube with the widest opening turned upward. - Insert the screw (m2) (long axis first) into the body (m1). - Fit the blade (m3) onto the short axis, the cutting sides facing outward. - Place the desired screen (m4) on the blade (m3) aligning the locking pins and the notches. - Screw the nut (m5) clockwise onto the body (m1), all the way but without locking it. The axis should not leave any play or rotate around itself. If this happens, dismantle and repeat the previous instructions. - Place the assembled head on the gear block assembly (l). USAGE AND PRACTICAL TIPS - Prepare the entire quantity of food to be minced. - Cut the meat or vegetables into pieces (approximately 2 x 2 cm). - Place a container under the mincer head. - Turn the speed selector (a2) to the 2 position to start. - Insert the meat through the feed tube, piece by piece, using the pusher (m7). - Never push with your fingers or any other utensil. - Do not run your appliance for more than 15 minutes when mincing meat. - Before mincing, make sure that your meat is thoroughly thawed. CLEANING THE MINCER HEAD - Before cleaning, always unplug your appliance. - Unlock the mincer head (ma) or (mb), tilting it toward the right to remove the gear block assembly (l). - To remove the mincer head, take the tray (m6) off the feed tube, unscrew the nut (m5), remove the screen (m4), the blade (m3) and the screw (m2). - Handle the cutting implements with care as they are sharp. - Wash all the parts in hot water and washing up liquid;; rinse and dry them thoroughly. - The screen (m4) and the blade (m3) must be kept oiled. [. . . ] Place the prepared pizza on your greased, floured baking sheet. Bake for 15 to 20 min, keeping an eye on it as it bakes. Substitute the bakers yeast with 1/2 teaspoon of Easy Bake or Fast Action dried yeast and add to the bowl with the flour, before adding the warm water. After processing, just shape the dough into a loaf and then leave to rise for about 1 hour in a warm place until doubled in size. [. . . ]