User manual MSI FM2-A75IA-E53

[. . . ] X) Mainboard G52-77211X2  Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks in this manual are properties of their respective owners. [. . . ] The JUSB1 and JUSB2 are controled by JUSB_PW1. These jumpers allow you to enable/ disable the “wakeup from S3/S4/S5 by USB and PS/2 device” function JUSB_PW1 (for on-board USB connectors) 1 1 1 Disabled Enabled JUSB_PW2 (for rear USB 2. 0 ports) 1 1 1 Disabled Enabled Important If you set the jumper to Enabled, the power supply must be able to provide +5VSB and at least 2A currents. 0 x1 slot PCI Slot The PCI slot supports LAN card, SCSI card, USB card, and other add-on cards that comply with PCI specifications. Important Make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to configure any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. PCI Interrupt Request Routing When adding or removing expansion cards, make the IRQ, acronym of interrupt request line and pronounced I-R-Q, are hardware lines over which devices can send interrupt signals to the microprocessor. The PCI IRQ pins are typically connected to the PCI bus pins as follows: Order Slot PCI 1 1 INT A# 2 INT B# 3 INT C# 4 INT D# 25 BIOS Setup Entering Power on the computer and the system will start the Power On Self Test (POST) process. When the message below appears on the screen, please <DEL> key to enter CLICK BIOS II: Press DEL key to enter Setup Menu, F11 to enter Boot Menu If the message disappears before you respond and you still need to enter CLICK BIOS II, restart the system by turning the computer OFF then back ON or pressing the RESET button. You may also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. Important The items under each BIOS category described in this chapter are under continuous update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be held for reference only. overview After entering Click BIOS II , the following screen is displayed. Language Temperature monitor Mode selection BIOS menu selection BIOS menu selection System information Boot menu Boot device priority bar Menu display Important The pictures in this guide are for reference only and may vary from the product you purchased. Please refer to the actual screens of your system for detailed information. Temperature monitor This block shows the temperature of the processor and the mainboard. 26 MS-7721 System information This block shows the time, date, CPU name, CPU frequency, DRAM frequency, DRAM capacity and the BIOS version. BIOS menu selection The following options are available: SETTINGS - Use this menu to specify your settings for chipset features and boot devices. oC - This menu contains items of the frequency and voltage adjustments. Increasing the frequency can get better performance, however high frequency and heat can cause instability, we do not recommend general users to overclock. eCO - This menu is related to energy-saving settings. BROWSER - This feature is used to enter the MSI Winki web browser. [. . . ] 33 Install Windows XP Notes This section describes how to install Windows XP with IDE or AHCI mode. Installing Windows XP with IDE Mode You will fail and encounter a blue screen while installing Windows XP, because it is not natively supported to be installed in the storage device with AHCI mode. If you still prefer to install Windows XP as the operating system, please change the BIOS item as below. Installing Windows XP with AHCI Mode If you prefer to install Windows XP as the operating system with AHCI mode, please prepare AHCI drivers for Windows XP in advanced. [. . . ]