User manual MSI MS-7522 V5.0 V5.0

[. . . ] X58A-GD45 series MS-7522 (v5. x) Mainboard G52-75221XE Preface Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. MSI® is registered trademark of Micro-Star Int'l Co. , Ltd. NVIDIA® is registered trademark of NVIDIA Corporation. [. . . ] Settings are: [Off] Always leaves the computer in the power off state. [On] Always leaves the computer in the power on state. [Last State] Restore the system to the status before power failure or interrupt occurred. Wake Up Event Setup Press <Enter> and the following sub-menu appears. Chapter 3 Wake up Event By Setting to [BIOS] activates the following fields, and use the following fields to set the wake up events. Setting to [OS], the wake up events will be defined by OS. Resume From S3 By USB Device The item allows the activity of the USB device to wake up the system from S3 (Suspend to RAM) sleep state. Resume From S3 By PS/2 Keyboard / Mouse These items determine whether the system will be awakened from what power saving modes when input signal of the PS/2 keyboard/ mouse is detected. Resume By PCI-E Device When set to [Enabled], the feature allows your system to be awakened from the power saving modes through any event on PCIE device. Resume By RTC Alarm The field is used to enable or disable the feature of booting up the system on a scheduled time/date. Date/ HH:MM:SS If Resume By RTC Alarm is set to [Enabled], the system will automatically resume (boot up) on a specific date/hour/minute/second specified in these fields (using the <+> and <-> to select the date & time settings). Available settings for each item are: [Date] 01 ~ 31, Every Day [HH:MM:SS] 00 ~ 23 : 00 ~ 59 : 00 ~ 59 3-13 BIOS Setup H/W Monitor Chassis Intrusion The field enables or disables the feature of recording the chassis intrusion status and issuing a warning message if the chassis is once opened. To clear the warning message, set the field to [Reset]. The setting of the field will automatically return to [Enabled] later. CPU Smart FAN Target The mainboard provides the Smart Fan function which can control the CPU fan speed automatically depending on the current temperature to keep it with in a specific range. If the current CPU fan temperature reaches to the target value, the smart fan function will be activated. It provides several sections to speed up for cooling down automatically. SYS FAN 1/ 2 Control These items allow users to select how percentage of speed for the SYSFAN1/ 2/ 3/ 4. PC Health Status CPU/ System Temperature, CPU FAN/ SYS FAN 1/ 2 Speed, CPU Vcore, 3. 3V, 5V, 12V These items display the current status of all of the monitored hardware devices/components such as CPU voltage, temperatures and all fans' speeds. 3-14 MS-7522 Green Power Chapter 3 CPU Phase Control When set to [Auto], the hardware will auto adjust the CPU power phase according to the loading of CPU to reach the best power saving function. Motherboard LED Control This item is used to turn on (Auto)/ turn off (Disabled) the power phase LEDs of the mainboard. ----- GreenPower Genie---- Icore/ I12V/ Vcore/ V12V These items show the amperage of I core/ V core/ I12V/ V12V. Pout/ Efficiency These items show the power consumption & efficiency of the system. 3-15 BIOS Setup BIOS Setting Password When you select this function, a message as below will appear on the screen: U-Key This item is used to enable/ disable USB driver device as a key. [. . . ] In the [Topology] pane, scroll to "Virtual Disk" (VD 0: XXXX), and press Enter to select. Scroll to "Rebuild" and press Enter to configure the rebuild process. Marvell BIOS Setup (c) xxxx Marvell Technology Group Ltd. Topology HBA 0: Marvell 0 Virtual Disks VD 0: MRAID1 PD 8: ST3750330MS [Delete] Free Physical Disks [Rebuild] PD 0: ST3750XXX Information ID Namd Status Stripe Size RAID Mode Size BGA Status Number of PDs Members : : : : : : : : : 0 MRAID1 Degrade 64K RAID1 953344MB N/A 2 08 Appendix C Appendix C 4. Scroll through the list of free disks, and press Space to select a replacement physical disk. [. . . ]