User manual MTD ZYJ209A

[. . . ] is set to ON; controls the effects in the same manner as operating the EXP PEDAL. Is set to PC ONLY or PC+BANK, this is received via the MIDI channel selected in the Effects Channel setting and is used to switch the insert effects. Bank Select and Program numbers correspond to the insert effect patch banks and numbers as shown below. Received via bass MIDI channel when the MIDI parameter ?Bass Ch. [. . . ] Is set to PC+BANK, this is transmitted via the MIDI channel selected in the Effects Ch. Setting when insert effects patches are switched. 02 n = MIDI channel number: vv = Volume: * Received via each track?s MIDI channel when the MIDI parameter ?MIDI Fader?is set to ON; controls the track volume. 9 343 MIDI Implementation System Realtime Message Timing Clock Status F8H * Received during creation of sync tracks in the Sync Track screen. 16) 00H - 7FH (0 - 127) 00H - 7FH (0 - 127) Start Status FAH * Received when creation of the sync track begins in the Sync Track screen. 16) 00H - 7FH (0 - 127) 01H - 7FH (1 - 127) Stop Status FCH * Received when creation of the sync track is finished in the Sync Track screen. N = MIDI channel number: kk = Note number: vv = Note on velocity: * * * * Active Sensing Status FEH * When Active Sensing is received, the unit will begin monitoring the intervals of all further messages. While monitoring, if the interval between messages exceeds approximately 400 ms, the same processing will be carried out as when Reset All Controllers is received, and message interval monitoring will be halted. , ee = data: F7H: System Exclusive Message status an ID number (manufacturer ID) to indicate the manufacturer whose Exclusive message this is. ID numbers 7EH and 7FH are extensions of the MIDI standard; Universal Non-realtime Messages (7EH) and Universal Realtime Messages (7FH). will be transmitted when the ZYJ209A is running (recording or playing). The transmitted time counts are summed to ?SMPTE (MTC) Offset Time?* Transmitted according to the content of the SMF during playback of SMFs. Is set to PC ONLY or PC+BANK, this is transmitted via the MIDI channel selected in the Effects Channel setting when insert effects patches are switched. For the correspondence between Bank Select/Program numbers and the insert effect patch banks/numbers, see ???. 16) 00H - 7FH (0 - 127) n = MIDI channel number: vv = Channel Pressure: * Transmitted according to the content of the SMF during playback of SMFs. (0-29) xxyyyyyy Reserved (00) Seconds (0-59) xxyyyyyy Reserved (00) Minutes (0-59) Transmitted according to the content of the SMF during playback of SMFs. Channel Mode Messages * Transmitted according to the content of the SMF during playback of SMFs. 16) Hours Count xyyzzzzz x Reserved (0) yy Time Code Type * The time code types defined by the MIDI specification correspond to the ZYJ209A Sync parameter ?MTC Type?16) mm, nn=Song position point: * The current position is transmitted by the Song Position Pointer Message when the BR1200CD is stopped, or the locate operation has been performed, if the SYNC parameter ?Sync Gen. Byte Remarks F0H Exclusive status 7FH Universal System Exclusive Realtime Header Dev Device ID (7FH) 06H MMC command message 01H STOP (MCS) F7H EOX (End of Exclusive) * If the transport switch [STOP] was pressed, the ZYJ209A transmits this message. [. . . ] Status F0H Byte F0H 7FH Dev 06H 06H F7H * Data byte 7FH, Dev, 06H, 06H Status F7H System Exclusive Messages Universal System Exclusive Message Identity Reply Message * Receiving Identity Request Message, the ZYJ209A send this message. Data byte 7EH, dev, 06H, 02H, 41H, 71H, 01H 00H, 00H, 00H, 00H, 00H, 00H Status F7H Remarks Exclusive status Universal System Exclusive Realtime Header Device ID (7FH) MMC command message RECORD STROBE EOX (End of Exclusive) Transmitted when recording to the audio tracks begins. RECORD EXIT Status F0H Data byte 7FH, Dev, 06H, 07H Status F7H Status F0H Byte F0H 7EH dev 06H 02H 41H 0AH 02H 00H 00H 00H 00H 00H 00H F7H Remarks Exclusive status ID number (Universal Non-realtime Message) Device ID (dev: 10H - 1FH) Sub ID#1 (General Information) Sub ID#2 (Identity Reply) ID number (Roland) Device family code Device family number code Software revision level EOX (End of Exclusive) Byte Remarks F0H Exclusive status 7FH Universal System Exclusive Realtime Header Dev Device ID (7FH) 06H MMC command message 07H RECORD EXIT F7H EOX (End of Exclusive) * Transmitted when recording to the audio tracks ends. MMC RESET Status F0H Data byte 7FH, Dev, 06H, 0DH Status F7H For instructions on setting the device ID, refer to ?How to set the device ID:? [. . . ]