User manual MULLER MARTINI CONTROL CONSOLE 2500

[. . . ] Müller Martini Druckmaschinen GmbH Operating Manual Control Console 2500 Serial Number Article Number of Operating Manual 2500. 4002. 71 Alprinta 52/74 Control Console Table of Contents 2500 1 1. 1 Introduction 1-1 3 Control Console of Alprinta . . 2 2. 1 2. 1. 1 2. 1. 2 2. 1. 3 2. 2 2. 2. 1 2. 2. 2 2. 3 2. 3. 1 2. 3. 2 2. 4 2. 4. 1 2. 5 2. 5. 1 2. 6 2. 6. 1 2. 6. 2 2. 6. 3 2. 6. 4 Safety Guidelines 2-1 3 3 3 4 4 4 4 5 5 5 6 6 6 6 7 7 7 9 10 General . Operating Manuals for Machine Stations . Local Laws, Guidelines and Regulations . [. . . ] This setting is immediately active when the counter is turned on, without confirmation of the dialog box with . Actual value Display the actually reached number of printed products in the batch run. When the counter is on this value changes continuously based on the counting direction set until the set value of the batch run is reached. 02. 2009 Müller Martini Druckmaschinen GmbH 2500. 4002. 71 6 - 13 Control Console Counter Use during Production Alprinta 52/74 2500 The mentioned setting values of the batch run can be entered before the counter is turned on. Effective counting of the printed products only begins after the counter is turned on with the Hotkey button . If the machine is stopped when the counter is turned on, the numerical display of the batch run as well as the progress display of the total run stops at the actual count reached. With activated end stop the machine stops after reaching the batch run. The warning Batch Run Reached and End Stop Selected is displayed. Afterward the counter must be reset with Reset, the machine started again and the counter turned on with . After the counter reset the indication is automatically dimmed out. When the end stop is deactivated the machine does not stop after reaching the batch count. The warning Batch Count Reached is displayed and the counter is automatically reset, while the total run counter continues. With every counter reset, the number below the progress display bar in the Production screen is reset to zero or a set value depending on the counting direction and the count is incrementally increased or decreased The display in the counter field of the Production screen is only updated after confirming the dialog box Counter with . 6 - 14 2500. 4002. 71 Müller Martini Druckmaschinen GmbH 02. 2009 Alprinta 52/74 Control Console Counter Use during Production 2500 C. Register Card Totalizer No settings can be made in the register card Totalizer . This register card contains the actual value of the total length of paper travel in meter, e. g. here the entire run distance of the machine is displayed. The display "Totalizer not resetable" cannot be deleted, corrected or set to zero and comprises all paper usage, even if the counter is turned off. The value "resettable" can be reset to zero by clicking on the key . The measurement unit of the counter can be set in the basic configuration. Settings for counting are possible in meter, feet and rotations print cylinder (last printing unit engaged). As soon as the machine is started the first time, the totalizer monitors the paper consumption in this field. The totalizer display is for information only and can be used to monitor the actual waste, and efficiency of the printing. 02. 2009 Müller Martini Druckmaschinen GmbH 2500. 4002. 71 6 - 15 Control Console Counter Use during Production Alprinta 52/74 2500 D. Register Card Counting Format In the register card Counting Format the print product and to mark the run. you can make settings for the count format of 6 - 16 2500. 4002. 71 Müller Martini Druckmaschinen GmbH 02. 2009 Alprinta 52/74 Control Console Counter Use during Production 2500 With this function you can: Counting format Enter the counting format of the actual print image on the sheet into a numerical entry field for finishing in the delivery (see chapter 3. 5. 2 , , Entry of Numerical Value", page 3-41). 24 inches) does not always agree with the format of the actual image. The count format always refers to the format of the actual image, which can be printed twice (12 inches) on the sheet. [. . . ] . 02. 2009 Müller Martini Druckmaschinen GmbH 2500. 4002. 71 13 - 7 Control Console Index Alprinta 52/74 2500 Pre-spray duration . Process Wash-Up / Inking Up / Set-Up Process Wash-Up / Inking-Up / Set-Up Processing Unit Configuration . 7-3 13 - 14 13 - 7 5 - 79 5 - 38 9 - 27 . 9-5 5 - 81 5 - 51 4 - 24 6 - 32 5 - 52 5 - 49 . [. . . ]