User manual MULLER-ELECTRONIK SPRAY CONTROL S

[. . . ] Installation and User´s Guide SPRAY-Control S December 1994 --------------------- Datei: SPRAY-Control-S_English. DOC [24. 11. 00] Contents 1. Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Fitting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Specified implementation also includes adhering to the operating and maintenance conditions stipulated by the manufacturer. The relevant accident prevention regulations as well as other generally recognized safety, industrial medical and road traffic rules must be adhered to. The manufacturer also accepts no liability in cases where changes have been made to the SPRAY-Control S independently. 2. 5. 2. Safety instructions Before working with electrical equipment or carrying out any welding operations on the tractor or the trailed machines, the battery connection must be interrupted. Copyright Müller-Elektronik GmbH & Co. , Salzkotten Installation and User`s Guide SPRAY-Control S (12/94) Seite - 9 - Seite - 10 - Copyright Müller-Elektronik GmbH & Co. , Salzkotten Installation and User's Guide SPRAY-Control S (12/94) 3. 3. 1. Operating instructions Description of the functions · Display The SPRAY-Control S has an 8-digit numerical display. During operation the current speed (km/h) and the spray rate (l/ha) can be read at a glance. The display shows the machine data and the operating data selected The "on" and "off" keys are on the left beside the display. The control lamps "distance impulse" (wheel / cardan shaft / radar), "boom section" and "working position" are on the right. The "boom section" lamp lights up when one or more boom sections are switched off. The "working position" lamp must light up when spraying is in progress. · Decimal keyboard The decimal keyboard can be used to carry out the four basic arithmetical functions and to enter machine data. · Operating data This keypad can be used to retrieve data required. By pressing the "Enter" and "C" keys simultaneously, the order is started. All numbers except ha and l are set to 0. · Machine data This keypad is used to communicate the machine data to the computer. With the "+/-10%" keys it is possible to vary the spray rate in degrees of 10% in relation to the preset rate 3. 2. Description of the machine data Before the device is ready for operation, the machine data must be entered. 3. 2. 1. "Working width" key This key is used to enter the working width > Press the "working width" key > The value is entered via the decimal keyboard > Press the "enter" key (=) Copyright Müller-Elektronik GmbH & Co. , Salzkotten Installation and User`s Guide SPRAY-Control S (12/94) Seite - 11 - 3. 2. 2. "Km/h sensor" key The SPRAY-Control S has 3 inputs to record the distance travelled. The sensors X - wheel / cardan shaft and radar - can be connected to the tractor signal distributor and the sensor X (field sprayer wheel) can be connected to the machine signal distributor. The SPRAY-Control S can only evaluate one sensor during an operation process. The "km/h" key is used for the selection. Enter 1 = wheel / cardan shaft sensor 2 = radar 3 = wheel - attached sprayer For all three inputs the calibration rate "impulses/100 m" can be stored. The sensor selection can be changed during operation. wheel / cardan shaft) > Press the "km/h - sensor" key > Press "1" > Press the "enter" key (=) 3. 2. 3. "Impulses / 100 m" key This key is used to enter the number of impulses which the installed sensor (see 3. 2. 2. ) communicates to the computer. The rate impulses / 100 m is known > Press "impulses / 100 m" key > Enter the rate via the decimal keyboard > Press the "enter" key (=) Note! [. . . ] The working position has not been recognized, The "main switch" lamp is not lit. The spray rate l/ha is continually "Impulses/l" have not been displayed at "0". Impulses from the liquid flow meter are not reaching the computer. The spray rate display is not The liquid flow meter is not correct. [. . . ]