User manual MURATEC M-750

[. . . ] Muratec, the Muratec logo and all Muratec fax product names contained herein are trademarks of Muratec America, Inc. ENERGY STAR is a registered mark of the United States Environmental Protection Agency. ® Welcome to your Muratec fax/copier! We know you want to use your machine now, without first having to climb over a mountain of jargon. So we've divided these instructions into three sections. · "Getting started" (see page 1. 1) covers only what you absolutely have to know to use your machine immediately. [. . . ] Your machine will receive and print out the document. Use the numeric keypad to enter a two-digit count of the number of pages in your document, based on what you counted in step 2. If there are fewer than 10 pages, enter a leading zero and then the number (e. g. , 04 for four pages). Press ENTER. Enter Fax Number _ Responding to a call request If someone requests a call from you during a fax communication, you'll hear a long ring after the receiving machine has received each page. To answer the call request: From here, proceed normally with the desired type of transmission. When the remote fax machine prints your document, a note on the right side of your TTI will indicate the number of the page -- such as "P. 02" for page two. The power of QuadAccess Your fax's QuadAccess feature sharply reduces the time you might otherwise spend waiting for the machine to finish its work and let you get back to your own work. QuadAccess is a more powerful version of what already is a pretty powerful feature, called dual access. While a fax with normal dual access performs one memory operation, you can do a second operation: set up a memory or delayed transmission, print a report, make settings (including on the autodialer) or even make copies. But your fax's QuadAccess allows a you to perform four operations at once. For example, even if you are (1) sending a fax and (2) making a copy, you can still (3) scan in a document for faxing or copying and (4) program the fax for anything you would like, without the machine slowing down. 1. 2. Lift your machine's optional handset, and listen for a few seconds. You may hear a brief series of fax tones. Otherwise, proceed to step 5. 5. To change the setting, press PROGRAM once or twice until your desired setting appears. In this example, we've chosen "On. " Opr. Protect: On Program/Enter 6. Press ENTER to save the setting. Press ENTER to save the passcode. Anytime you want to turn off the passcode, change the passcode back to 0000 by repeating steps 1­7 and entering 0000 in step 6. 2. 36 Beyond the basics Using your fax machine during operation protection Activating security reception 1. 2. When you press any key on your machine, the display will show: Operation Protected Enter Passcode :**** 1. 4. If the machine is in Fax mode, proceed to step 2. If it is in Copy mode, press COPY/FAX to change to Fax mode. Press PROGRAM, O (the letter O, not a zero), 1, ENTER. The display shows: Set Security Rx Enter Passcode :**** Use the numeric keypad to enter the four-digit passcode (here, we've entered the passcode we set previously; see page 2. 36). Operation Protected Enter Passcode :6296 Use the numeric keypad to enter the passcode. Here, we've entered 6296: Set Security Rx Enter Passcode :6296 If you make an error, press or until the cursor appears under the character you wish to change; then enter the correct character. When you enter correct passcode, the machine will let you go on to the next step in the fax operation. Note: If you start an operation while the first is still underway (see "The power of TriAccess, " page 2. 35), the machine will require the passcode from you once again before proceeding with your new request. [. . . ] AI. 6 AI. 5 Appendix and index Limited warranty This warranty is made by Muratec America, Inc. (hereafter referred to as "Muratec"). This warranty is valid only on Muratec products purchased and used in the United States of America. This warranty applies to the product only while owned and used by the original purchaser ("Customer"). [. . . ]