User manual MURATEC MFX-2500

[. . . ] Muratec MFX-2500 Operating Instructions General Reference Welcome . . . Trademarks Muratec, the Muratec logo and all Muratec product names contained herein are trademarks of Muratec America, Inc. ENERGY STAR is a registered mark of the United States Environmental Protection Agency. Copyright Copyright 2000 by Muratec America, Inc, All rights reserved. As an Energy Star partner, Muratec America, Inc. , has determined that this product meets the Energy Star guidelines for energy efficiency. Super G3 is an extension of Group 3 fax technology standards, allowing the use of high-speed ITU-T V. 34 bis modems for 33. 6 Kbps transmission and high-speed protocols for rapid handshaking. JBIG -- Joint Bi-level Image experts Group, the new ITU-T standard image data compression method. As JBIG compresses the data more efficiently than MMR, it is especially effective when transmitting halftone (grayscale) image document. This manual and any updates to it can be found online at www. muratec. com Go to the "Products" section of this site, then click on "MFX-2500" Regulatory information United States of America Federal Communications Commission (FCC) information Ringer Equivalence Number (RENs): AC REN, 2. 2B; DC REN, 0. 3. [. . . ] The list includes each key's number, the Location ID (if any), fax/telephone number and group number(s) you've stored in the key. To print a list of one-touch numbers, press MENU, A, [List]. 14 Use the numeric keypad to enter the call groups for this number. There are 32 possible call groups, numbered 132. If you want to assign the number to more than one call group, insert a comma after each number (except the last one) by pressing [Add]. Note: To assign this number to all 32 call groups, enter 0 (zero). 15 16 Press [Enter] to save the setting. If you do want to enter another one-touch number, go back to step 2. If you do not want to enter any more one-touch numbers, press RESET to finish. Use the autodialer labels in your fax's packaging to write down the stored numbers for easy reference. If you have entered the group number, you can also print out a directory of your call groups. (See page 2. 7. ) 2. 3 Beyond the Basics One-touch fax dialing To dial a fax call using a one-touch number: Using speed-dial numbers Your fax machine can store up to 222 speed-dial numbers, designated by three-digit identifier codes from 001 through 222. 1 2 3 Place the document and select resolution and contrast you require. Toggle between transmission from the feeder or from memory if necessary, by pressing MEMORY TRANSMIT. Press the one-touch key in which you've stored the number. Entering or changing a speed-dial number One-touch phone dialing To dial a phone call using a one-touch number, you must have an optional handset attached to your machine. (Contact your authorized Muratec dealer to order an optional handset. ) To make the call: 1 2 Press MENU, B, [Enter]. The LCD shows the speed-dial number list. Select the speed-dial number in which you want to store a number or change a previously stored number. Note: You can select the speed-dial number by directly entering that three-digit identifier code. When entering the identifier code for speed-dial numbers less than 100, you must enter leading zeroes to make three digits. Note: You can press [Detail] to see the number which has been programmed in that speed-dial number. Use the numeric keypad to enter the number exactly as your machine should dial it, including whatever access codes your phone system requires. (You may want to review "Special dialing characters, " page 2. 1. ) The number can be up to 40 characters in length. Note: You must enter the fax number to program the speed-dial number. Note: If a fax number is already registered in this speed-dial number, the number is shown on the LCD. If you wish to change the fax number, press the [Clear] to erase it and then enter another number. [. . . ] This speed depends upon the modem speed of each unit, the resolution setting, the content of the document, the encoding technique and the condition of the phone line (clean, noisy, etc. ) Any change in any one of these five conditions will affect the speed, sometimes significantly. V. 29 and v. 27 ter -- A standard set of communication procedures allowing fax machines to talk to other units using those standards. Specifically, these standards cover fax transmission at 9600 bps or slower. V. 34 -- An international standard for fax modems -- and other modems -- with transmission speeds of up to 28. 8 Kbps. The V. 34 protocol is sometimes referred to as "V. Fast", because it represented a significant increase in possible transmission speed compared to the transmission protocol it replaced. V. 34 bis -- A faster version of the V. 34 standard, and sometimes referred to as "V. 34 Plus" or "V. 34 +". [. . . ]