User manual MUSTEK POWERMUST 2016S NETGUARD VIEWPOWER

[. . . ] ViewPower User's Manual Management Software for Uninterruptible Power Supply Systems Table of Contents 1. ViewPower Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ModBus Communication Setting It will display all connected PCs through ModBus. Step 1 Select Viewpower configuration>>Certificates Management. Refer to Diagram 4-10. 23 Diagram 4-10 Step 2 Password setting/change menu for ModBus. Real-time control will be available when the ModBus password is the same to the UPS password. port setting: The default ID for nominated com. port is 0; Selectable baud rates are 1200, 2400, 4800, 9600, and 19200. The default setting is 4800; Selectable data bit is 7 and 8. The default setting is 8; Selectable stop bit is 1 and 2. The default setting is 1; Supported parity is ODD parity, event parity and NONE. NOTE: This function is only available for the UPS with ModBus communication port. 4. 1. 9. Certificates management If using Exchange Server for mailbox system, it's required to configure ExChange server domain name in this screen. 24 Select Viewpower configuration>> Certificates management. Refer to Diagram 4-11. Diagram 4-11 4. 2. Local Shutdown It's shutdown setting for local PC which is directly connected to monitored UPS with communication port. This configuration enables system shutdown of local PC or to remote shut down PCs which are powered by monitored UPS. Step 1 Select UPS Setting >> Local Shutdown or click shortcut icon Diagram 4-12. Refer to 25 Diagram 4-12 NOTE: This screen may be different for different types of UPSs. Step 2 Select shutdown conditions and power-off options, set delay time to shutdown system. Step 3 Enter time for pop-up dialog before shutdown and warning interval in Warning Dialog Setting area. Step 4 Click "Apply" button to save all data. NOTE: Click "Default" button to recover the default setting. Conditions: UPS works on battery mode Local system shutdown after xx min xx sec: When clicking the checkbox, local PC will start to shut down after monitored UPS works on battery mode for xx min xx sec time. The maximum setting number for minutes is 999, and for seconds is 59. Local system shutdown when UPS is at low battery level: When clicking this checkbox, local PC will shut down when monitored UPS is at low battery level. Allows local system shutdown when UPS is scheduled off: When clicking this checkbox, the local system will shut down before monitored UPS is scheduled to 26 power off. [. . . ] Users still can retrieve old data saved in the software even though the UPS is no longer connected to local system. Step 3 Select the starting time and ending time by clicking calendar icon. Then click "Browse" button to get the data table. "Print": Print the listed data table. [. . . ]