User manual NAD C325BEE

[. . . ] 1 Read instructions - All the safety and operating instructions should be read before the product is operated. 2 Retain instructions - The safety and operating instructions should be retained for future reference. 3 Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4 Follow Instructions - All operating and use instructions should be followed. [. . . ] In such a case, turn the amplifier off by the rear panel POWER button, wait for it to cool down and/or check the speaker connections, making sure the overall loudspeaker impedance doesn't go below 4 ohms. Once the cause for the protection circuitry to engage has been removed, switch ON the rear POWER button and then the Standby Button to resume normal operation. TAPE 1 is a tape Monitor function which does not override the current input selection. Mute does not affect recordings made using the Tape outputs but will affect the signal going to the Pre-amp output (Pre Out). REAR PANEL CONNECTIONS 1 IR Input / output - This input is connected to the output of an IR (infrared) repeater (Xantech or similar), or the IR output of another component to allow control of the C325BEE from a remote location. Ask your dealer or custom installer for further details. 2 Disc input - Input for additional line level input signals such as CD, Mini Disc player or the output signal from a step-up amplifier for a turntable. Use a twin RCA-to-RCA lead to connect the auxiliary unit's left and right `Audio Outputs' to this input. 3 CD input - Input for a CD or other line-level signal source. Use a twin RCA-to-RCA lead to connect the CD player's left and right `Audio Outputs' to this input. The NAD C325BEE only accepts analogue signals from your CD player. 4 Video input - Input for the audio signal from a stereo VCR (or stereo TV/Satellite/Cable receiver) or other line-level audio source. Using twin RCA-to-RCA leads, connect to the left and right `Audio Outputs' of the unit to these inputs. 5 AUX input - Input for additional line level input signals such as another CD player. Use a twin RCA-to-RCA lead to connect the auxiliary unit's left and right `Audio Outputs' to this input. 6 Tuner input - Input for a tuner or other line-level signal source. Use a twin RCA-to-RCA lead to connect the tuner left and right `Audio Outputs' to this input. 7 Tape 2 In/Out - Connections for analogue recording and playback to an audio tape recorder of any type. Using twin RCA-to-RCA leads, connect to the left and right `Audio Output' of the tape machine to the TAPE 2 IN sockets for playback and tape monitoring. Using twin RCA-to-RCA leads, connect to the left and right `Audio Output' of the tape machine to the TAPE 1 IN sockets for playback and tape monitoring. connect the left and right `Audio Input' of the tape machine to the TAPE 1 OUT sockets for recording. 9 Pre out - Connections to an external power amplifier or processor, such as a surround-sound decoder. [. . . ] Power AC lead unplugged or power not switched on Tape 1 Monitor selected · Check if AC lead is plugged in and power switched on De-select Tape 1 Monitor mode IR receiver in direct sun or very bright ambient light Amplifier has overheated Place unit away from direct sun, reduce amount of ambient light Turn amplifier off, make sure ventilation slots on top and bottom of amplifier are not blocked. After amplifier has cooled down, turn back on Rated power) Maximum input signal Signal / Noise ratio A-weighted 1 Signal / noise ratio pre-amp out, A-weighted Frequency response 20Hz - 20kHz THD + Noise, SMPTE IM FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS SVENSKA Line level outputs Output impedance Maximum output level POWER AMP SECTION Continuous output power into 8 2 Rated distortion (THD 20Hz - 20kHz) Clipping power (maximum continuous power per channel 4 and 8) IHF Dynamic headroom 8 4 IHF dynamic power (maximum short term power per channel) 8 4 2 Damping factor (ref. PHYSICAL SPECIFICATIONS Dimensions (W x H x D)6 Net weight Shipping weight 2 Minimum power per channel, 20Hz - 20kHz, both channels driven with no more than rated distortion. 3 Total harmonic distortion, 20Hz - 20kHz from 250mW to rated output 4 Intermodulation distortion, 60Hz - 7kHz, 4:1, from 250mW to rated output 5 CCIF IM distortion, 19 + 20kHz rated output 6 Gross dimensions include feet, volume knob and extended speaker terminals. [. . . ]