User manual NAD C355BEE

[. . . ] Readinstructions- All the safety and operating instructions should be read before the product is operated. Retaininstructions- The safety and operating instructions should be retained for future reference. FollowInstructions- All operating and use instructions should be followed. Cleaning- Unplug this product from the wall outlet before cleaning. [. . . ] It is motor driven and can be adjusted from the remote control handset. The VOLUME control does not affect recordings made using the Tape outputs but will affect the signal going to the Pre-amp output (PRE OUT 1 or PRE OUT 2). Mute does not affect recordings made using the Tape outputs but will affect the signal going to the Preamp output (PRE OUT 1 or PRE OUT 2). 1 RS-232: Connect this interface via RS-232 serial cable (not supplied) to any Windows® compatible PC to allow remote control of the C 355BEE through NAD's proprietary PC software or other compatible external controllers. nAD is a certified partner of AMX and Crestron and fully supports these external devices. See your NAD audio specialist for more information. 2 12VTRIGGEROUTPUT: The 12V TRIGGER OUTPUT is used for controlling external equipment that is equipped with a 12V trigger input. This output will be 12V when the C 355BEE is ON and 0V when the unit is either OFF or in standby. This output can drive a load up to 50mA at 12V. 3 IRIN/OUT: These mini-jacks accept and output remote-controlled codes in electrical format, using industry-standard protocols, for use with "IR-repeater" and multi-room systems and related technologies. IRIN: This input is connected to the output of an IR (infrared) repeater (Xantech or similar) or the IR output of another component to allow control of the C 355BEE from a remote location. IROUT: When connected to the IR IN of an ancillary equipment, direct the ancillary equipment's own remote control to the C 355BEE's infrared receiver to command or control the linked unit. All NAD products with IR IN/IR OUT features are fully compatible with the C 355BEE. For non-NAD models, please check with your other product's service specialists as to their compatibility to the C 355BEE's IR features. 4 DISCINPUT: Input for additional line level input signals such as CD, Mini Disc player or the output signal from a step-up amplifier for a turntable. Use a twin RCA-to-RCA lead to connect the auxiliary unit's left and right `Audio Outputs' to this input. Use a twin RCA-to-RCA lead to connect the CD player's left and right `Audio Outputs' to this input. The NAD C 355BEE only accepts analogue signals from your CD player. 6 VIDEOINPUT: Input for the audio signal from a stereo VCR (or stereo TV/Satellite/Cable receiver) or other line-level audio source. Using twin RCA-to-RCA leads, connect to the left and right `Audio Outputs' of the unit to these inputs. 7 AUXINPUT: Input for additional line level input signals such as another CD player. Use a twin RCA-to-RCA lead to connect the auxiliary unit's left and right `Audio Outputs' to this input. [. . . ] After amplifier has cooled down, turn back ON. 1W Signal / noise ratio pre-amp out, A-weighted 110dB ref. 01% at 5V out LINELEVELOUTPUTS Output impedance - Pre-out Tape Maximum output level - Pre-out Tape TONECONTROLS Treble Bass TRIGGEROUT Output resistance Output current Output voltage <120 50mA 12V ±5dB at 10kHz ±8dB at 100Hz 80 Source Z + 1k >11V >10V Continuous output power into 8 Rated distortion (THD 20Hz - 20kHz) Clipping power (maximum continuous power per channel 4 and 8 ) IHF Dynamic headroom - 8 4 IHF dynamic power (maximum short term power per channel) - 8 4 2 Damping factor (ref. Dimensions (W x H x D) - Net Gross Net weight Shipping weight 435 x 116 x 292mm 435 x 130 x 338mm 8. [. . . ]