User manual NAD T765 HD

[. . . ] ® Owner's Manual AV Surround Sound Receiver T 765 SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH IMPORTANT SAFETY INSTRUCTIONS ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA 1. Readinstructions- All the safety and operating instructions should be read before the product is operated. Retaininstructions- The safety and operating instructions should be retained for future reference. HeedWarnings- All warnings on the product and in the operating instructions should be adhered to. [. . . ] When set to `Variable' and while at the `Zone Controls' menu OSD, the Zone 2 Volume level can be adjusted using the HTR 3's or the corresponding front panel navigation buttons or directly via ZR 4's VOL . On the other hand, if Volume is set to `Fixed, ' the Zone 2 Volume is set to a preset dB level and thereafter the Zone's volume can be varied via the volume control of the separate amplifier it is fed into. MODE Zone 3 and Zone 4 can be configured into two modes ­ Record Out and Zone (Audio Only). If the selected mode is Record Out, the audio and applicable video signal of the assigned Source are directly sent out to the applicable Audio/Video Output (See Item 5. AUDIO 3 OUT/VIDEO 3 OUT/S-VIDEO 3 OUT, AUDIO 4 OUT/VIDEO 4 OUT/SVIDEO 4 OUT of REAR PANEL discussion. ) When Zone 3 or Zone 4 is set to `Record Out' mode, they will not be available at the `Zone Controls' section of the Main Menu window. `Record Out' setting is ideal for making recordings with a VCR or other similar devices. This setting is also used for multi-zone installations using passive `impedance matching' volume controls. See your NAD dealer for specific information about integrating your NAD Receiver into a multi-room audio distribution system. Zone 2 and Zone 3 `Volume' will function the same way as that of Zone 2 when `Mode' is set to `Zone (Audio Only). ' See discussion also on `Zone Controls' at the Setup Menu. AMPLIFIER SETUP If the surround back speakers are not used in the main zone, their surround back amplifier channels could be assigned for Main back, Main Front (Bi-Amp) and multi-zone use. The Surround Back amplifier is configurable through the following settings · MainBack: Assign as surround back speakers. · MainFront(Bi-Amp): Provide a bi-amp mode for the Main Front speakers (Left and Right) speakers thus reproducing the Front Left and Front Right amplifier channel outputs. · Zone2: Assign the surround back amplifier channels to supply Zone 2 speaker level outputs from the surround back speaker terminals. · Zone3: Assign the surround back amplifier channels to supply Zone 3 speaker level outputs from the surround back speaker terminals. · Zone4: Assign the surround back amplifier channels to supply Zone 4 speaker level outputs from the surround back speaker terminals. 5 SVENSKA NEDERLANDS DEUTSCH NOTE TheZR4remotecontrolwillonlycontrolZone2applications. ITALIANO ESPAÑOL FRANÇAIS ENGLISH OPERATION USINGTHET765­SETUPMENU ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA TRIGGER SETUP The T 765 features three configurable +12V DC Trigger Output that can be used to activate a component or system it is fed into. A Trigger Input is also available to turn on the applicable link it is associated to. Use a combination of or ENTER and keys to navigate through the Trigger Setup menu parameters. TRIGGEROUT Triggers are low voltage signals used to turn on/off other compliant devices. The T 765's three +12V DC Trigger Outputs (Trigger 1 Out, Trigger 2 Out and Trigger 3 Out) are dependent on which mode they are associated with. There are six choices where +12V DC output can be assigned and these are ­ Main, Zone 2, Zone 3, Zone 4, Zone 2+3+4 and Source Setup. Main: +12V DC is available at the assigned Trigger Out when the T 765 is at powered state. Zone2, Zone3, Zone4, Zone2+3+4: When the applicable Zone is at powered state, +12V DC is available at the assigned Trigger Out. SourceSetup: If Trigger Output is linked to `Source Setup, ' +12V DC is available at Trigger Out whenever the particularly assigned Source is selected. [. . . ] · IR transmitter window on remote or IR A/V Receiver window on T 765 is obstructed. · T 765 front panel is in very bright sunlight or ambient light. · Reduce sunlight/room lighting. · Power-down the T 765 via the rear panel Power switch and unplug it from the AC outlet. · Wait five minutes, re-connect and power up. [. . . ]