User manual NAD T785 HD

[. . . ] ® Owner's Manual AV Surround Sound Receiver T 785 SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH IMPORTANT SAFETY INSTRUCTIONS ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA 1. Readinstructions- All the safety and operating instructions should be read before the product is operated. Retaininstructions- The safety and operating instructions should be retained for future reference. HeedWarnings- All warnings on the product and in the operating instructions should be adhered to. [. . . ] When set to `Variable' and while at the `Zone Controls' menu OSD, the Zone 2 Volume level can be adjusted using the HTRC 1's or the corresponding front panel navigation buttons or directly via ZR 4's VOL . On the other hand, if Volume is set to `Fixed, ' the Zone 2 Volume is set to a preset dB level and thereafter the Zone's volume can be varied via the volume control of the separate amplifier it is fed into. MODE Zone 3 and Zone 4 can be configured into two modes ­ Record Out and Zone (Audio Only). If the selected mode is Record Out, the audio and applicable video signal of the assigned Source are directly sent out to the applicable Audio/Video Output (See Item 5. AUDIO 3 OUT/VIDEO 3 OUT/SVIDEO 3 OUT, AUDIO 4 OUT/VIDEO 4 OUT/SVIDEO 4 OUT of REAR PANEL discussion. ) When Zone 3 or Zone 4 is set to `Record Out' mode, they will not be available at the `Zone Controls' section of the Main Menu window. `Record Out' setting is ideal for making recordings with a VCR or other similar devices. This setting is also used for multi-zone installations using passive `impedance matching' volume controls. See your NAD dealer for specific information about integrating your NAD Receiver into a multi-room audio distribution system. Zone 2 and Zone 3 `Volume' will function the same way as that of Zone 2 when `Mode' is set to `Zone (Audio Only). ' See discussion also on `Zone Controls' at the Main Menu. NOTE TheZR4remotecontrolwillonlycontrolZone2applications. You can make changes to the relative levels of center, surround and subwoofer outputs without having to go into the `Speaker Levels' menu. This is very convenient in circumstances like increasing (or tone down) a film's dialog level by raising (lowering) the center channel or reducing excessive deep bass (or enhance deep bass) by lowering (raising) the subwoofer level. Use the HTRC 1's 'SURR, ' `CENT' and `SUB' keys for direct-access level adjustment of these channels over a range of ±6 dB. The surround back channels (if any) adjust in lockstep with the surround channels. NOTE Levelsettingsadjusted`OntheFly'areaddedorsubtractedtothesetup levelsestablishedattheT785level-calibrationroutineasinvokedbythe HTRC1`Test'key. However, selectinganyPresetwillrevertthechannel levelstothosestoredinthepreset. ItwillalsotakeT785offthelevelsset viaAudysseyAutoCalibration. ZONE SETUP AMPLIFIER SETUP NEDERLANDS SVENSKA If the surround back speakers are not used in the main zone, their surround back amplifier channels could be assigned for Main back, Main Front (BiAmp) and multi-zone use. The Surround Back amplifier is configurable through the following settings · MainBack: Assign as surround back speakers. · MainFront(Bi-Amp): Provide a bi-amp mode for the Main Front speakers (Left and Right) speakers thus reproducing the Front Left and Front Right amplifier channel outputs. · Zone2: Assign the surround back amplifier channels to supply Zone 2 speaker level outputs from the surround back speaker terminals. · Zone3: Assign the surround back amplifier channels to supply Zone 3 speaker level outputs from the surround back speaker terminals. · Zone4: Assign the surround back amplifier channels to supply Zone 4 speaker level outputs from the surround back speaker terminals. 6 OPERATION USINGTHET785­SETUPMENU TRIGGER SETUP LISTENING MODE SETUP TRIGGEROUT Triggers are low voltage signals used to turn on/off other compliant devices. The T 785's three +12V DC Trigger Outputs (Trigger 1 Out, Trigger 2 Out and Trigger 3 Out) are dependent on which mode they are associated with. There are six choices where +12V DC output can be assigned and these are ­ Main, Zone 2, Zone 3, Zone 4, Zone 2+3+4 and Source Setup. Main: +12V DC is available at the assigned Trigger Out when the T 785 is at powered state. [. . . ] · Switch 12V TRIGGER IN/OUT to OFF position. Novideodisplay. · Resolution setting is not supported by the TV/Monitor. · Batteries are flat or incorrectly inserted. · IR transmitter window on remote or IR A/V Receiver window on T 785 is obstructed. · T 785 front panel is in very bright sunlight or ambient light. T785doesnotrespondtoHTRC1remote. T785doesnotrespondtofrontpanel commandsorremotecontrol. · Microprocessor error. [. . . ]