User manual NADY TMP-1

[. . . ] 5 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 State _____________________ Zip _____________________ SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Model # ____________________________________________ LEGAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Before installing and using your unit, carefully examine the packaging and all contents for any signs of physical damage that may have occurred in transit. (Note: Nady Systems is not responsible for shipping damage. If the unit is damaged, do not return to us, but notify your dealer and the shipping company immediately to make a claim. Such claims must be made by the consignee in a timely manner. ) CONTENTS: · Instruction manual · TMP-1 (verify that the unit's serial number is same as shown on shipping carton) · AC Power cord · Warranty Card RACK MOUNTING The TMP-1 fits into one standard 19" rack unit of space (1 3/4"). Parts of the unit can become very warm during use. Care should be taken to ensure that there is enough space around the unit for cooling (at least 12" or 30cm). Do not place the TMP-1 on high temperature devices such as power amplifiers, etc. , or the unit may overheat in operation. Also, do not place the unit on speakers as this may cause them to move and/or fall due to speaker vibrations. Although the unit's chassis is shielded against radio frequency (RF) and electromagnetic interference (EMI), extremely high fields of RF and EMI should be avoided. POWER CONNECTION The TMP-1 has an internal power supply and is designed to operate from an external AC source. Power requirements for electrical equipment differ from area to area. Be sure to confirm that the voltage selected by the voltage selector switch on the back panel is proper for your area (120VAC/60 Hz or 230VAC/50Hz) per the information below: Europe (except UK): 230V, 50Hz UK and Australia: 240V, 50Hz USA and Canada: 120V, 60 Hz For other areas, please check with local authorities. When ready to operate, plug the AC cord into the power source. Make sure that the unit is turned off before connecting to the AC power source to avoid possible loud transients which can damage your speakers or your ears, especially when monitoring with headphones. 4 CONTROLS AND CONNECTORS FRONT PANEL (2) (3) (4) (5) (6) (7) (8) (9) (1) Front Panel (1) POWER SWITCH Use this switch to power unit ON or OFF. The integrated LED will light when the unit is ON. Before turning on this unit, verify connection to the proper voltage AC source, check all connections and turn down the level controls of equipment connected to the outputs. (Note: The TMP-1 will not output audio for approximately 16 seconds after power up due to the time it takes for the tubes to warm up. Do not turn up the audio until after this warm up period to avoid possibly damaging speakers or your hearing due to improper level settings. ) (2) INPUT CONTROL The INPUT CONTROL sets the amount of input gain of the TMP-1, turn the control clockwise to increase gain and counterclockwise to decrease gain. You may control two ranges of gain with this control, +26 to +60dB and +6 to +40dB. Selection of the gain range is made with the +20dB GAIN SWITCH (3) (3) +20dB GAIN/NORM SWITCH Use the +20dB GAIN/NORM switch to set the gain range of the INPUT CONTROL (2). When the switch is out, the TMP-1 operates in Normal mode, depressing the switch adds 20dBs of gain. For microphone applications, where more level is needed, push the switch in. (4) PHANTOM POWER SWITCH Use the PHANTOM POWER to supply power to all microphones requiring +48V phantom power. The TMP-1 phantom power is engaged and disengaged with this switch Phantom power is applied to pins 2 and 3 of the XLR INPUT (13) jacks when this switch is pushed in. To disengage phantom power, position the switch in the out position. (5) OUTPUT LEVEL VU METER The output level of the TMP-1 can be monitored using the analog OUTPUT LEVEL VU METER. [. . . ] 0. 1% S/N Ratio: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >94dB Tone Controls Bass: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +/-12dB / 100Hz Treble: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +/-12dB / 10KHz Inputs: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]