User manual NADY UB-33B

[. . . ] typical (depending on site conditions); up to 500+ feet optimum line-of-sight CONTENTS CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 USING THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Slip the transmitter into a pocket or CLIP (23) it onto your clothes or instrument strap. Turn on the UB-33B by sliding the audio AUDIO SWITCH (19) to the OFF position first then slide the POWER SWITCH (21) to the ON position. The Bi-Color LED indicator (20) will stay on (GREEN), indicating usable battery strength and that the transmitter is on. In the case of dead or low batteries, the LED will either not go on at all or will stay on (ORANGE) continuously, indicating that the batteries should be replaced with fresh ones. To preserve battery life, turn the transmitter off when not in use. The A or B Diversity LED indicators (13) on the U-33 receiver should now be lit, indicating a received signal from the transmitter. Instrument Use Secure the connection from the GT CABLE (24) by turning the slip ring on the plug into the transmitter clockwise to thread it on the jack. Plug the 1/4" phone plug into the instrument. When ready to play, slide the AUDIO SWITCH (19) to "ON" position. Adjust the volume of the receiver as per the Audio Output Instrument Connection section of the above U-33B receiver instruction. (Note: The UB-33B is supplied with a removable antenna. It should be operated with the supplied antenna all times. For optimum operating range, always maintain lineof-sight between the transmitter and the receiver whenever possible. ) U-33B RECEIVER 1. Rackmounting the Receiver There are 2 options available for rackmounting the U-33B receiver: singly or side-byside with another U-33B receiver. Single mounting: Remove the receiver SIDE MOUNT CLIP (1) from each side of the receiver (as shown) and slide in the optional ERM-3 RACK EARS (2). Side-by-side double mounting: After removing the SIDE MOUNT CLIPS (1) from both U-33B receivers, join the two receivers with the EJC-3 JOINING CLIP (3) and attach the ERM-33 RACK EARS (4) as shown. (Note: Do not mount the receiver in a rack directly above an amplifier or other source of high heat ­ this could degrade the performance of the U-33B. Always ensure adequate airflow and heat dissipation in any rack configuration. ) 2. Powering the Receiver Plug the 18V AC/DC ADAPTER (5) provided into the DC INPUT JACK (9) on the back of the receiver. Then plug the power supply into an AC outlet. (Note: Any 18V DC source with 250mA capability can also be used. ) Press the POWER SWITCH (11) once to turn on the receiver. The POWER ON LED (12) will now light and the receiver is operational. [. . . ] This is a low-pass filter, with up to 6 dB of gain, over flat respsonse centered in the 30-300Hz, when turned fully clockwise. The normal wireless sound is with the control left fully counterclockwise. Connecting the Audio Output The U-33B receiver provides both a fixed mic level BALANCED AUDIO OUTPUT XLR (7) and an adjustable line level UNBALANCED AUDIO OUTPUT 1/4" JACK (10). The level from the UNBALANCED OUTPUT is controlled by the rear panel VOLUME CONTROL (8). [. . . ]