User manual NADY UHF-3

[. . . ] Side-by-side double mounting: After removing the SIDE MOUNT CLIPS (1) from both UHF-3 receivers, join the two receivers with the EJC-3 JOINING CLIP (3) and attach the ERM-33 RACK EARS (4) as shown. (Note: Do not mount the receiver in a rack directly above an amplifier or other source of high heat ­ this could degrade the performance of the UHF-3. Always ensure adequate airflow and heat dissipation in any rack configuration. ) 2. Powering the Receiver Plug the 12V AC/DC ADAPTER (5) provided into the DC INPUT JACK (9) on the back of the receiver. [. . . ] Occasional flickering of the top AF Peak LED indicator on loud inputs to the transmitter is normal. If this LED lights continuously, decrease the volume to the transmitter or overload distortion may result. 4 5 UH-3 HANDHELD MICROPHONE TRANSMITTER 15 15 Unscrew the BATTERY COMPARTMENT COVER (16) and remove, exposing the BATTERY HOLDER (17). Insert 2 fresh AA ALKALINE BATTERIES (18), observing the correct polarity as marked, and screw the cover back on to the microphone. Make sure the cover is screwed on completely. Fresh alkaline batteries can last up to 10 hours in use, but in order to ensure optimum performance, it is recommended that you replace the batteries after every 7-8 hours of use. Turn on the UH-3 by sliding the audio MUTE SWITCH (19) to the OFF position first. Then slide the POWER SWITCH (21) to the ON position. The battery indicator LED (20) will give a single quick flash, indicating usable battery strength. In the case of a dead or low battery, the LED will either not go on at all or will stay on continuously, indicating that the batteries should be replaced with fresh ones. To preserve battery life, turn the transmitter off when not in use. The A and/or B DIVERSITY LED INDICATORS (13) on the UHF-3 receiver should now be lit, indicating a received signal from the transmitter. When ready to speak, slide the audio MUTE SWITCH (19) to the ON position. Adjust the volume of the receiver as per the Audio Output Microphone Connection section of the above UHF-3 receiver instructions. volume, transmitter location and speaker placement so that acoustic feedback (howling or screeching) will be avoided. ] 12 11 14 13 10 9 8 7 6 5 18 17 1 2 2 21 4 1 16 3 4 22 19 20 6 7 UB-3 BODYPACK MICROPHONE TRANSMITTER 1. Open the hinged BATTERY DOOR (23) and insert 2 fresh AAA ALKALINE BATTERIES into the BATTERY COMPARTMENT (24), observing the correct polarity. Fresh alkaline batteries can last up to 5 hours in use, but in order to ensure optimum performance, it is recommended that the batteries be replaced after 3-4 hours of use. The UB-3 is equipped with an INPUT SELECTOR SWITCH (32) located under the cover for selecting the type of audio input you will be supplying to the transmitter. Select from the choice of three positions: INSTRUMENT (for guitar, bass, etc. )/ HEADWORN MIC/ LAVALIER MIC. The UB-3 is provided with a 3. 5 mm LOCKING JACK (26) for connecting the audio input selected. Connect either the INSTRUMENT CORD (34) or the HEADWORN MIC (35) or LAVALIER MIC CORD (36) as desired, according to the input selected. (Note: Use only the input audio source as per the input selected with the AUDIO INPUT SELECTOR SWITCH or the audio will not be optimal­a muddy or distorted sound may result. ) To secure the connection, turn the slip ring on the plug clock wise to thread it on the jack. Slip the transmitter into a pocket or CLIP (33) it on to your clothes or instrument strap (if using the UB-3 as an instrument transmitter). [. . . ] Make sure the R/A Number is clearly marked on the outside of the package and enclose a cashier's check or money order (if not prepaid with a credit card). Ship the unit prepaid to: Nady Systems, Inc. , Service Department, 6701 Shellmound Street, Emeryville, CA 94608. Include a brief description of the problems you are experiencing. The warranty card enclosed with this system contains additional valuable warranty and service information. [. . . ]