User manual NAIM CD5 ISSUE 2

[. . . ] WORLD CLASS HI FI OWNERS MANUAL CD Players: CDS3, CDX2, CD5 ISSUE 2 Introduction Naim Audio products are always conceived with performance as the top priority and careful installation will help ensure that their full potential is achieved. This manual begins with statutory safety warnings and general installation tips for all Naim Audio products. Product specific information begins in Section 6. 2 CONTENTS Page Section 1 1 1 1 Equipment Installation 2 Cables and Connections 3 Getting Started 3. 1 switching on and off 3. 2 running in 3. 3 mains supply 3. 4 siting the equipment 3. 5 if you have a problem 4 Warnings 5 Connection 5. 1 mains lead 5. 2 mains plugs 5. 3 fuse carrier 5. 4 plug fuses 6 CDS3 Installation and Operation 7 CDS3 Rear Panel and Connection Diagrams 8 CDS3 Operation Diagrams 9 CDX2 Installation and Operation 1 Equipment Installation Normally your Naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended to reduce this responsibility in any way. 2 3 4 2 Cables and Connections Please do not modify the standard interconnect cables supplied with your Naim equipment. [. . . ] Further information on play list programming can be found in Sections 15 and 16. All CD control functions are duplicated on the NARCOM 3 and Flash remote handsets. The handsets also provide CD programming facilities. See Sections 15 and 16 for more information. ®, HDCD®, High Definition Compatible Digital® and Pacific MicrosonicsTM are either registered trademarks or trademarks of Pacific Microsonics, Inc. in the United States and/or other countries. 9 CDX2 9. 5 output Socket Selection A pair of phono output sockets are fitted at the rear of the CDX2 to provide an alternative to the preferred DIN socket. Proceed as follows to select the phono sockets. With the player stopped, press and hold the remote handset disp function (handset in CD mode) until the CD player prog text indicator flashes. Further operations of the disp function will now cycle through each combination of the two socket types (DIN only, phono only or both). The selected option is indicated on the CD player display as shown below. Socket Option DIN Phono Both Player Display 9. 7 player maintenance It is important for reliable operation of the CDX2 to ensure that the surfaces of the transport platter and the underside of the puck are free of dust or debris which can prevent the disc from sitting properly and cause it to slip. To clean the transport platter, take a piece of Blu-tack and lightly apply it to the top surface of the magnetic metal hub, picking up any material attached to it. Brush the plastic outer edge lightly with your finger or a soft brush to ensure that it is dust and particle free. Similarly, clean the puck with Blu-tack, to remove debris from the three locating pins on its underside. Take care not to damage the rubber pressure pads. Brush them lightly with your finger or a soft cloth. Do not, under any circumstances, use any solvents or fluids for the cleaning process. O o0 O o0 Press and hold the disp function a second time to exit from socket selection mode. 9. 6 power supply upgrade The CDX2 can be upgraded by the addition of an XPS Power Supply. The XPS takes over from the internal power supply of the CDX2 and offers both a greater number of separate supplies and more sophisticated voltage regulation. The XPS is connected to the CDX2 via a heavy duty "Burndy" cable. Switch off both the XPS and CDX2 when making connections. Connect the Burndy cable ensuring that the connectors are securely attached and their twist lock mechanisms are engaged. Switch on the XPS from its front panel power button. After a short while the CDX2 will function as normal. 10 CDX2 10. 1 CDX2 Rear power mains input Note optional RS232 data port RC5 input link plug fitted alternative RCA phono output sockets to preamplifier The RC5 input fitted to the CDX2 is intended to accept external control signals for multi-room applications. Contact your dealer for further information on its use. CDX2 Output ch1 out ch 2 out -ve nc nc 10. 2 CDX2 Connected to XPS Power Supply CDX2 XPS mains input Note When used with an XPS the CDX2 must be disconnected from the mains. [. . . ] A second press restores the volume. Toggles between mono and stereo operation. The tuner display will indicate stereo when both stereo operation is selected and a stereo signal is received. The mono button on the tuner will illuminate when mono is selected. 19 Narcom 3 Handset 16. 4 soft keys These keys operate functions depending on the System Component Key setting. numeric keypad: In preamp mode the numeric keys will switch between the preamplifier inputs. [. . . ]