User manual NAIM1 NA-P 300 AMPLIFIER MANUAL

[. . . ] owners manuaL PreamPLIFIers InTeGraTeD amPLIFIers, Power amPLIFIers enGLIsH DeuTsCH FranÇaIs ITaLIan0 Cont ent s Page section saFeTY InsTruCTIons In order to comply with current european safety regulations it is essential that the naim loudspeaker connectors supplied with amplifiers and loudspeakers are used. Do not under any circumstances allow anyone to modify your naim equipment without first checking with the factory, your retailer, or your distributor. unauthorised modifications will invalidate your guarantee. equipment must not be exposed to dripping or splashing and no objects filled with liquid, such as vases, should be placed on the equipment. [. . . ] Switch on the external power supply and then the Supernait when all connections are complete. should always be connected regardless of what other equipment is used in conjunction with the amplifier. The mains earth only grounds the case and the electrostatic screen within the transformer, and is not connected to the signal negative. In order to avoid hum loops, the signal negative of the whole system should be connected to the mains earth (ground) in one place. 19. 9 G eneral C o nne c tio ns no te s The Supernait negative input and output connections for each channel are common. The mains earth (ground) 20 suPernaIT Controls and Connections 20. 1 s uP e rn aI T F ro nt source and record selection source bank record bank volume balance mute combined analogue and digital input headphone output analogue Phono RCA inputs digital inputs 20 . 2 s uP e rnaI T re ar outputs RC5 in/out 1 2 3 4 bi-amp sub tape aux1 av tape tuner cd power mains input and fuse left RS232 interface speaker tape and av Inputs ch1 ch2 -ve right speaker signal ground power amp in and preamp out. aux 2 input aux 2 av in tape tuner cd in in & & out in & in power out out cd and tuner Inputs ch1 ch2 -ve nc nc ch1 (out) ch2 (out) +ve ch2 -ve +ve ch1 note: The RS232 interface is an optional upgrade. It can be specified at time of order or fitted retrospectively. Contact your local representative or Naim Audio directly for further information. note: The link plug should be removed only if a power supply upgrade is to be used or an alternative preamplifier is to use the Supernait power amplifier section. It should remain fitted in all other circumstances. e19 pre-amp out for bi-amp ch2 -ve ch1 nc SU P E R N A IT Integr a ted Ampl i fi er 20. 3 s uP e rn aI T C o nne c te d to H i- C a p P ow er s u p p l y power mains input and fuse cable direction marker Interconnect Cables 4 to 4 pin DIN 240° 5 to 5 pin DIN mains input and fuse 20. 4 s uP e rn aI T C o nne c te d to naP 2 0 0 P ow er a m p l i f i er power mains input and fuse mains input and fuse cable direction marker Interconnect Cables 4 to 4 pin DIN e20 SU P E R N A IT Integr a ted Ampl i fi er 20. 5 s uP e rn aI T C o nne c te d to H i- C a p P ow er s u p p l y a n d n a P 2 0 0 P ow er a m p l i fi er power mains input and fuse cable direction marker Interconnect Cables 4 to 4 pin DIN 240° 5 to 5 pin DIN mains input and fuse mains input and fuse 21 suPer n a I T sp eci f i ca ti on Input sensitivities: overload margins: Preamp output Level: Tape output Level: Power output: auxiliary Power outputs: Quiescent Consumption: Dimensions (H x w x D): weight: mains supply: 75mV, 47k 40dB (all inputs all audio frequencies) 0. 775V, <50 75mV, 600 Continuous 80 Watts per channel into 8 Ohms For Naim phono stage 10VA 87 x 432 x 314mm 12. 8kg 100-120V or 220-240V, 50/60Hz e21 N A I T X S Integr a ted Ampl i fi er 2 2 naI T Xs Introd ucti o n, Instal l a ti on a nd C onnecti ons The naIT Xs should be installed on a dedicated equipment stand intended for the purpose. Do not stand it directly on top of another item of equipment. Care should be taken to ensure that it is level. The amplifier should be installed in its final location before connecting cables or switching on. ensure that the volume is turned down before switching on. a variety of power supply upgrade, alternative preamplifier and alternative or additional power amplifier options are possible for the naIT Xs. Diagrams illustrating the connection of some of these are shown in section 23. Contact your local retailer or distributor for advice on further alternative connection schemes. The NAIT XS incorporates an AV Bypass switch on its rear panel. The switch should only be set to "On" if the amplifier is to be used in conjunction with an AV processor in a home theatre system. In all other installations the AV Bypass switch should be set to "Off". Speaker and/or amplifier damage may occur if a signal is inadvertently connected to the NAIT XS av input while the AV Bypass switch is "On". operational features common to all preamplifiers and integrated amplifiers are described in section 28. operational features common to all preamplifiers and integrated amplifiers are described in section 28 22. 1 mains P owe r C o nne c tio n Connect the NAIT XS to a mains power socket using either the mains cable supplied or a Naim Power-Line. 2 2 . [. . . ] The three channels provide power to drive a centre channel speaker and a pair of either main front or surround channel speakers. audio line level input is via two 4-pin DIn sockets - one for the centre channel and one for the main or surround pair. The NAPV 175 should be installed on an equipment rack intended for the purpose and in its final location before connecting cables or switching on. switch on the source and preamplifier components, with the volume turned down, before switching on the NAPV 175. [. . . ]