User manual NAPCO GEM-RP3DGTL

[. . . ] OPERATING GUIDE for your GEM-RP3DGTL KEYPAD GEMINI 96 US TAT ED S RM A SYSTEM ARMED 01/01/97 12:00AM ENT A1 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME A B C 1 4 7 2 5 8 3 6 9 D 0 E F G AREA PRIOR/NO NEXT/YES COMPUTERIZED SECURITY SYSTEM R © NAPCO 1999 DESIGN PATS. PENDING 1 GEM-RP3DGTL. pub page 1 Wednesday, August 18, 1999 14:03 INTRODUCTION The GEM-RP3DGTL is a "smart", interactive, menu-driven keypad designed for your Napco control panel. A digital display is provided to show the status of your system. This booklet contains important information about the operation of your system with this GEM-RP3DGTL Keypad. [. . . ] System troubles display and sound at the keypad. Correcting the trouble will clear most indications, however the following error codes will require manual reset: E11; E13; E19; E20 and E22. (See SYSTEM TROUBLE ERROR CODES for a description of error codes. ) 10. If accidentally enabled, press the C button to exit. INTERIOR BYPASS FIRE/TBL SYS TBL CHIME INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 11. YES NO. ) In Commercial Burglary systems, exit delay may have been programmed to start after a central-station "ringback" (verification) signal has been received. If the ringback tone has not been received within about 30 seconds after arming, a communication problem may exist. Use this function to start exit delay manually, then exit the premises immediately. Be sure to have your alarm specialist check communications with the central station as soon as possible. If accidentally enabled, press the C button to exit. 12 13 18 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 13. If accidentally enabled, press the C button to exit. INTERIOR BYPASS FIRE/TBL SYS TBL CHIME GEM-RP3DGTL. pub page 18 Wednesday, August 18, 1999 14:03 KEYPAD FUNCTIONS 14 15 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 14. If accidentally enabled, press the C button to exit. YES NO. ) Sends a communicator test to the central station. A communication failure will be indicated at the keypad by a system trouble "3" display. Repeat the test to attempt to correct a communication failure, as any successful communication will clear this display. (Not for UL-listed systems. ) Allows automatic arming to be delayed up to 4 hours, 15 minutes, as follows: INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 16 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME For a 1-hour, 15-minute delay, press [1], then the Jbutton. For a 2-hour, 15-minute delay, press [2], then the Jbutton. For a 3-hour, 15-minute delay, press [3], then the Jbutton. For a 4-hour, 15-minute delay, press [4], then the Jbutton. Fifteen minutes prior to arming, the siren will sound a 2-second warning and the keypad will begin a 15-minute countdown with the sounder pulsing. During this time, arming may be delayed an additional 1 to 4 hours (as above), or autoarming may be cancelled by arming and disarming the panel. 19 GEM-RP3DGTL. pub page 19 Wednesday, August 18, 1999 14:03 KEYPAD FUNCTIONS 17 18 INTERIOR BYPASS FIRE/TBL SYS TBL CHIME 17. YES NO. ) Activates the Program Mode from Keypad No. [. . . ] In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional, shipping costs prepaid and insured to NAPCO. After repair or replacement, NAPCO assumes the cost of returning products under warranty. NAPCO shall have no obligation under this warranty, or otherwise, if the product has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial numbers have been altered, defaced or removed. [. . . ]