User manual NAPOLEON GRILLS PTH38PSS

[. . . ] Do not use the heater in an explosive atmosphere. Keep the heater away from areas where gasoline or other flammable liquids or vapors are stored. Prior to use, check for damaged parts such as hoses, regulators, pilot or burner. The installation of fixed appliances shall only be carried out by competent persons and be in accordance with the relevant Codes of Practice. [. . . ] 10 16 3 7 ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 5 9 10 Step 5 ---- Attach Center Reflector to Reflector Attach center reflector to the top of reflector (4 pcs) by M6 X 10 mm screws (12 pcs) , 6mm washers (12 pcs) and nuts (12 pcs). 1 15 2 Step 6 ---- Attach Center Reflector and Reflector to the top of Head Assembly Load center reflector and reflector to the top of head assembly by M6 X 70 double pointed bolts (3 pcs) 6mm washers (3 pcs) and nuts (3 pcs) Step 6 9 10 3 8 ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 7 ---- Connect Gas Line to Cylinder Attach Gas hose to regulator with 3/8 Inch Open End Wrench and Adjustable Wrench. Move cylinder to the plate of base assembly. Step 7 Step 8 ---- Check for leak Your Patio Heater has been checked at all factory connections for leaks, To check the Connection of the gas hose/regulator/cylinder. 1) Make leak solution by mixing 1part liquid dish soap and 3 parts water. 2) Spoon several drops (or use squirt bottle) of the solution onto the gas hose/regulator and regulator/cylinder connection. 3) Inspect the connections and look for bubbles. 4) If no bubbles appear, the connection is safe. 5) If bubble appear, there is leak, loosen and re-tighten this connection. Step 8 9 ASSEMBLY WARNING : TO BE INSTALLED ONLY BY A COMPETENT PERSON Step 9---- Lower Cylinder Cover onto Cylinder Base Lower the cylinder cover onto the cylinder base . Step 9 6 8 Step 10---- Disconnect Cylinder When Storing or Transporting 1). Turn off the heater; 2). Upper the cylinder cover onto the post mounts; 3). Turn off the valve of the cylinder; 4). Loosen the screw of cylinder and regulator; 5). Disconnect the cylinder from regulator. Step 10 6 7 10 OPERATION WARNING: DO NOT attempt to operate heater until you have read and understand all precautions. Failure to do so can result in serious personal injury, death or property damage. Before Turning Gas Supply ON FOR YOUR SAFETY: WA R N I N G Your heater was designed and approved for OUTDOOR USE ONLY. Do NOT use it inside a building , or any other enclosed area. Make sure surrounding areas are free of combustible materials, gasoline and other flammable vapors or liquids. Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and there are no leaks. Be sure the access panel is clear of debris. Be sure any component removed during assembly or servicing is replaced and fastened prior to starting. If at any time you are unable to light burner and smell gas, wait 5 minutes to allow gas to dissipate before attempting to light heater. If, after 1 minute, you are unable to light burner, wait 5 minutes and allow flammable vapors to dissipate before attempting to light heater again. Before Lighting Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. If relighting a hot heater, always wait at least 5 minutes. Our heater is tested for quality assurance. Ignition attempts should succeed 8 out of 10 attempts. at least 45 minutes after use. Allow emitter and dome to cool before touching. FOR YOUR SAFETY: DO NOT touch or move heater for WA R N I N G LIGHTING INSTRUCTIONS 1) Turn the control knob to "OFF" position. [. . . ] Turn LP cylinder to "OFF" position. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). If desired, cover heater to protect exterior surfaces and to help prevent debris in air passages. During periods of extended inactivity or when transporting; Turn the control knob to "OFF" position. [. . . ]