User manual NAVIGON 1300

[. . . ] User's manual NAVIGON 13xx | 23xx English (United Kingdom) April 2009 The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-oflife. This applies to your device but also to any enhancements marked with this symbol. Do not dispose of these products as unsorted municipal waste. Imprint NAVIGON AG Schottmüllerstraße 20A D-20251 Hamburg The information contained herein may be changed at any time without prior notification. Neither this manual nor any parts thereof may be reproduced for any purpose whatsoever without the express written consent of NAVIGON AG, nor may they be transmitted in any form either electronically or mechanically, including photocopying and recording. [. . . ] If you have planned a route with only one route point and the MyRoutes function is activated, you will be prompted to select a route for the simulation. Tap on the button of the route on which you want to simulate the navigation. Note: When the MyRoutes function is deactivated or if you have planned a route with more than one route point, the simulation will start directly after the route has been calculated. For more details about the MyRoutes function refer to the chapter "MyRoutes" on page 35. Stopping simulation You can stop simulation at any time. Tap on (Back). - 40 - Navigation User's manual NAVIGON 13xx | 23xx The ROUTE PLANNING window opens. 5. 4. 7 Route preview You have calculated and displayed a route. The map is open in Preview mode. Route Profile The route is calculated on the basis of a route profile. The current settings are indicated by symbols on the Profile) button at the top right edge of the map. (Route If you now want to view or change the route profile, tap on Route Profile. Note: If you change the route profile, the changes will also apply to future navigations. Information about individual route profile settings can be obtained by tapping on the related (Help) button. Note: When you load routes which originate from a different provider than NAVIGON, the Route Profile button may be inactive. You cannot change the route profile of this route. Turn-by-Turn List If you want to see detailed directions for the route, tap on Options > Turn-by-Turn List. For details of the functions in the TURN-BY-TURN LIST window refer to chapter "Turn-by-Turn List" on page 55. MyRoutes When the MyRoutes function is activated, the navigation system calculates up to three routes on the basis of the currently selected route profile and shows them on the map in different colours (orange, green, blue) and with a number. For each route there is a button with the same number and a symbol in the same colour. When calculating the time of arrival or the trip time, the navigation system takes account of additional factors such as day of the week and time of day. The route which corresponds best to the selected route profile is marked with "MyRoute". Navigation - 41 - User's manual NAVIGON 13xx | 23xx Note: The MyRoutes function can be used only for routes with only one route point. For routes with two or more route points only one route is calculated and displayed, regardless of whether you have activated the function or not. Note: Even when the MyRoutes function is activated, sometimes only one additional route or no additional routes at all can be calculated for a particular route. No further suggestion is then shown on the button in question. Navigation Tap on the button of the route which you want to use for the navigation. No GPS reception If GPS signal reception is not good enough, the following message will appear: "GPS reception is currently not sufficient. Navigation starts automatically as soon as GPS reception is OK again. " You have the following options: Wait. As soon as GPS reception is good enough for determining your position, the route will be recalculated and navigation will begin. The map opens in Preview mode. 5. 5 Options Some windows offer options that lead to more functions. Tap on Options to open the options list. Tap on the option you would like to use. If you would like to quit the options list without selecting an option, tap on the Options button again. 2D/3D: Changes between 2D and 3D mode. The address specified will be added as a route point. (Refer to "Multi-leg routes" on page 37. ) Block: Opens a window in which you can block a section of the route lying ahead in order to calculate a route which avoids this section, e. g. [. . . ] 28 Nearby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Preview TMC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 T Take Me Home. . . . . . . . . . . . . . . . . . . . . . . . . . . . 33, 36 TMC Preview TMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]