User manual NAVMAN MULTI 3100

[. . . ] MULTI 3100 Installation and Operation Manual DRAFT Approved by translator Approved by Plastimo This document is still under review and is subject to change. Each completed stage to be marked with English . . . . . . . . . . . . . c o m NAVMAN MULTI 3100 Installation and Operation Manual NAVMAN 1 FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. [. . . ] Press + several times until the Countdown Timer Start Time screen is displayed: 7-3 Adjust start time 1 Press . The timer does not start now (to start the timer, see section 7-1). 7-1 Start countdown timer The timer starts at the start time (to adjust the start time, see section 7-3). 1 2 Press until the countdown timer is displayed. The timer displays On briefly and starts counting down from the start time. MULTI 3100 Installation and Operation Manual 11 NAVMAN 8 Systems of several instruments Several NAVMAN instruments can be connected together during installation to share data. There are two ways of connecting instruments together, NavBus or NMEA. 8-2 NavBus NavBus is a NAVMAN proprietary system. It is high speed and allows a wide range of data to be shared by the instruments. When instruments are connected by NavBus: If you change the units, alarms or calibration in one instrument, then the values will automatically change in all other instruments of the same type Each instrument can be assigned to a group of instruments (see section 10-2, step 3). If you change the backlight in an instrument in group 1, 2, 3 or 4 then the backlight will automatically change in the other instruments in the same group. If you change the backlight in an instrument in group 0 then no other instruments are affected. If an alarm sounds, mute it by pressing on any instrument which can display that alarm. For example, mute a depth alarm on any instrument that can display depth. If the unit does not have a depth or a speed/ temperature transducer fitted then the unit will automatically take depth, speed and temperature readings from another instrument, via NavBus, if the data is available. For more information, refer to the NavBus Installation and Operation manual. 8-1 NMEA NMEA is an industry standard. Speed, depth, temperature and log data may be output which can be read and displayed by any compatible NAVMAN (eg REPEAT 3100) or other NMEA instrument. Speed (RMC) can be received via NMEA and displayed by the MULTI 3100 (see section 10-1 for wiring). If an external RMC (speed) input is available from a GPS instrument, then you can set up the MULTI 3100 to use this for speed readings (see section 10-2, step 2); Note: A speed from a paddlewheel sensor is the speed that the boat is moving through the water. A speed from a GPS is the speed over the ground. If there is a current then these two speeds will be different. If a transducer is not fitted to the unit and the corresponding external data is not available then the displayed value will be 0 (for example, when using a GPS input for speed and no speed/temperature transducer is fitted then temperature displays as 0). 9 MULTI 3100 hardware 9-1 What comes with your MULTI 3100 The MULTI 3100 comes in several configurations. Standalone configuration MULTI 3100 unit with protective cover. In addition, the standalone configuration usually requires a depth transducer and a speed/temperature transducer (see section 9-3). Kit configuration The MULTI 3100 is available in several kit configurations with different grades of through hull transducer, with: The parts for the standalone configuration, listed above. [. . . ] Box 68 155 Newton, Auckland, New Zealand. Ph: +64 9 481 0500 Fax: +64 9 480 3176 e-mail: marine. sales@navman. com Website: www. navman. com ASIA China Peaceful Marine Electronics Co. Hong Kong, Guangzhou, Shanghai, Qindao, Dalian. E210, Huang Hua Gang Ke Mao Street, 81 Xian Lie Zhong Road, 510070 Guangzhou, China. [. . . ]