User manual NAVMAN S300

[. . . ] We recommend rinsing the S300 with fresh water after any exposure to salt water. CAUTION: Please ensure battery cover is in place during cleaning. Store the S300 away from direct sunlight or extreme heat sources. (Remove battery before storing for an extended period. ) 1. 3 Water resistance The Navman S300 GPS Sport. Tool is water resistant. 1-6 S300 NAVMAN S300 - General information 1. 4 Changing the battery Always shut down the S300 before changing the battery. Note: All system settings, and the calculated data that was stored at the last controlled shutdown*, are retained when the battery is removed. [. . . ] Press repeatedly until the screen appears as shown above. To set button beep status to start editing (setting status flashes). 1) Press 2) Press or to select On or OFF. 3) Press 4) Press to go to the next option, or hold to leave setup. 4. 1. 4 Set speed units Set units for speed (km/h or mph). km km/h SYSTEM SET speed units Access this option If necessary, press and hold to turn the power on and enter setup. Press repeatedly until the screen appears as shown above. To set speed units 1) Press to start editing (speed units flash). 4) Press to go to the next option, or hold to leave setup. Note: Distance is displayed in units that correspond to user selected speed units. For example, if you select speed units `km/h', then distance is displayed in `km'. S300 1-13 S300 - Setup NAVMAN 4. 1. 5 Set offset (set local time) This option lets you adjust the S300 to display local time*. You only need to do this once, unless operating the unit in a new time zone. (* By default the S300 displays GPS time. The S300 will perform all functions accurately without adjusting the offset to display your local time. ) Note: If you attempt to change the time offset before all GPS data are obtained, the screen displays `no GPS' and the antenna icon flashes until all GPS data are received. SYSTEM SET Access this option If necessary, press and hold to turn the power on and enter setup. Press repeatedly until the screen appears as shown above. To set local time to start editing (the screen now appears as shown 1) Press below). The date is displayed to ensure that adjustments are made in the correct direction. current time current date PM SYSTEM SET 2) Press repeatedly to set time display forward (press and hold to set time display forward quickly), or press repeatedly to set time display backward (press and hold to set time display backward quickly). 4) Press to go to the next option, or hold to exit setup. 1-14 S300 NAVMAN S300 - Setup 4. 1. 6 Editing settings (overview) settings edit editing details set 12hr set 24hr accept set (12hr) set (12hr) set (31-12) edit set (31-12) set 31-12 set 12-31 accept beep edit beep beep ON beep OFF accept set units (km/h) edit set units (km/h) set units (km/h) accept set units (mph) edit accept set offset time (date) KEY = press this button = press this button = press both buttons together S300 1-15 S300 - Normal operation NAVMAN 5. 0 Normal operation 5. 1 Modes Press to turn the power on and start normal operation. Press repeatedly to step through the modes (press and hold to cycle through the modes quickly). Modes are accessed in the order shown below. Press repeatedly until the screen appears as shown above. To set Zone status to start editing (zone status flashes). 1) Press 2) Press or to select ON or OFF. 3) Press 4) Press to go to the next mode. 5. 1. 5. 1 Zone (Minimum) This option lets you set the minimum target speed. target speed (MIN) MIN km/h ZONE SET Access this mode See section 5. 1. 5 for access to this mode. To set zone minimum 1) Press to start editing (target speed flashes). 2) Press repeatedly to increase value by 0. 5 (hold to increase values quickly), or press repeatedly to decrease value by 0. 5 (hold to decrease values quickly). 4) Press to go to the next mode. S300 1-19 S300 - Normal operation NAVMAN 5. 1. 5. 2 Zone (Maximum) This option lets you set the maximum target speed. target speed (MAX) km MAX km/h Access this mode See section 5. 1. 5 for access to this mode. [. . . ] Each of these disclaimers is in addition to, and does not reduce the effect of, any other disclaimer. No dealer has the authority to change this warranty. No event that voids any warranty of the Product will have any effect on these disclaimers or limitations of liability. This disclaimer will be construed under the laws of New Zealand without regard for any conflict of law rules. [. . . ]