User manual NAVMAN SPEED 2100

[. . . ] 4 Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Trip Log reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Total Log reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the correct reading is indicated, press and keys again for two and hold the seconds. Release both keys when the display shows the following: CAL SPd and MPH (statute miles) KPH (kilometres) Calibrating DISTANCE Against a Known Reference 1. keys for 5 Press and hold to exit N AVM AN SPEED 2100 Installation and Operation Manual 5 3. Release both keys when the display shows the following: 4. If the display indicates a reading different from key to the known distance, press the key to increase the reading or the decrease the reading. When the correct reading is indicated, press and keys again for two and hold the seconds. Release both keys when the display shows the following: CAL 4. If the temperature reading indicated is incorrect, press the key to increase the key to decrease the reading or the reading. When the correct reading is indicated, press and hold the and keys again for two seconds. Release both keys when the display shows the following: oF oC LOg °F / °C Selection Press and hold the key while powering up the instrument. The display will indicate the current unit of measure. oF oC Press either the or key until the desired unit and of measure is displayed. Press and hold the keys for two seconds. The current temperature will be displayed. Temperature Calibration To calibrate the TEMPERATURE: 1. Release both keys when the display shows the following: Press for 5 seconds CAL 6 N AVM AN SPEED 2100 Installation and Operation Manual 3 Installation Location The SPEED 2100 is designed for above or below deck installation. Select a position that is: · · · · · · On a flat surface At least 300mm (12") from a compass At least 500mm (20") from any radio Easy to read by the helmsman and crew Protected from physical damage Accessible to electrical cable connections Mounting The instrument panel must be 3mm to 19mm (1/8" to 3/4") in thickness. · · · Drill a 51mm (2") hole in the instrument panel. Remove brackets and insert the instrument so the back is flush with the instrument panel. Slide the bracket over the instrument and tighten the mounting nut until secure. Instrument Panel 51mm (2") Hole Mounting Nut Mounting Bracket Instrument Sealing Gasket N AVM AN SPEED 2100 Installation and Operation Manual 7 Wiring Connection · Keep electrical and transducer cables away from alternator or other noise generating electrical cables. Avoid connecting the instrument to power circuits that share loads with ignition, alternators, inverters and radio transmitters. Electrical power supply connections should always be as short as possible. Connect the red wire to the positive supply via a 1 amp fuse or a 1 amp circuit breaker. Connect the black wire to the electrical ground. [. . . ] 923/588 Thaprong Road, Alegre - RS, Brasil. Mahachai, Ph: +55 51 3242 9972 Muang, Samutsakhon 74000, e-mail: equinautic@equinautic. com. br Thailand. Ph: +66 34 411 919 N AVM AN SPEED 2100 Installation and Operation Manual MIDDLE EAST Lebanon and Syria Letro, Balco Stores, Moutran Street, Tripoli VIA Beirut. Ph: +961 6 624512 e-mail: balco@cyberia. net. lb United Arab Emirates Kuwait, Oman, Iran & Saudi Arabia Abdullah Moh'd Ibrahim Trading, opp Creak Rd. Ph: +971 4 229 1195 e-mail: mksq99@email. com AFRICA South Africa Pertec (Pty) Ltd Coastal, Division No. 16 Paarden Eiland Rd. [. . . ]