User manual NAVMAN VHF 7110

[. . . ] VHF 7110 Dual Station Radio Quick Start Guide and Installation Supplement www. navman. com FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] To step through the channels one at a time, press or to display each channel. To change channels rapidly, hold down or on the handset to scroll through the channels. · Base Unit and Microphone · · · Handset Select a Favourite Channel · Press 3CH to toggle through each of the three favourite channels until the desired channel is shown. 3CH Base Unit, Microphone and Handset Store 3 Favourite Channels · · Select the channel. Hold down 3CH to store this channel as your first favourite channel, CH1. · · Base Unit, Microphone and Handset 8 Repeat to store your second favourite channel as CH2. Repeat again to store your third favourite channel as CH3. 3CH NAVMAN VHF 7110 Quick Start Guide Scan/Stop Scanning a Favourite Channel · · Select the favourite channel. Press SCAN to scan the favourite channel and the priority channel in DUAL or TRI watch mode. · Press SCAN again to stop. SCAN Base Unit and Handset Scan all 3 Favourite Channels · Press 3CH . · Hold down SCAN to scan all three favourite channels and the priority channel. 3CH SCAN · Base Unit and Handset Press SCAN again to stop. Delete a Favourite Channel · · Select the favourite channel. Hold down 3CH until the setting (CH1, CH2 or CH3) disappears off the LCD. 3CH Base Unit and Handset Select ALL SCAN mode · Hold down SCAN to start scanning all channels (and the priority channel every 1. 8 seconds). NOTE: In Europe, scanning functions may be limited or blocked in some countries. When a signal is received, scanning stops at that channel. Press ENT to skip over an `always busy' channel and resume scanning. Base Unit and Handset SCAN · Press SCAN to stop at the current channel. 9 NAVMAN VHF 7110 Quick Start Guide Use the Intercom · On the VHF 7110 US, hold down H/L to enter INTERCOM mode. IC This disables the radio receiver except for incoming DSC calls. The intercom calls the other handset. On the VHF 7110 EU, press IC . · · Press PTT when invited. Press ESC to exit the INTERCOM mode, or place the handset back ON hook. H/L IC VHF 7110 US Base Unit, Microphone and Handset H/L VHF 7110 EU Select the Channel Bank (7110 US only) 1. Hold down CALL on the base unit MENU or handset to show the Radio Setup Menu. 2. Scroll to the channel bank you want (USA, International, or Canadian), then press ENT to select it. CALL MENU > UIC RADIO SETUP RING VOLUME INT SPEAKER UIC Base Unit and Handset > USA INT'L CANADA 10 NAVMAN VHF 7110 Quick Start Guide Making an Individual Call · Hold down CALL until the menu MENU appears on the LCD. · Use CH or CH to scroll through the menu listing to INDIVIDUAL then press ENT to show your buddy list. · Scroll through the buddy list to the buddy that you want to call, then press ENT . · Select the working channel and press ENT . · Base Unit and Microphone Press ENT again to send the call. The call will be acknowledged when it is received and the working channel is automatically selected. · Press PTT to talk and release PTT to receive a reply. CALL MENU > INDIVIDUAL LAST CALL GROUP DSC CALL · Hold down CALL until the menu MENU appears on the LCD. INDIVIDUAL MANUAL NEW BUDDY 1 > BUDDY 2 BUDDY 2 INDIVIDUAL ROUTINE > SET CHANNEL · Use or to scroll through the menu listing to INDIVIDUAL then press ENT to show your buddy list. · Scroll through the buddy list to the buddy that you want to call, then press ENT . · Select the working channel and press ENT . · Press ENT again to send the call. The call will be acknowledged when it is received and the working channel is automatically selected. Handset · Press PTT to talk and release PTT to receive a reply. 11 NAVMAN VHF 7110 Quick Start Guide Setting Up a Buddy List Use this to alphanumerically store a maximum of 20 favourite names and their associated MMSIDs for DSC calls. · · Press any key to stop the alarm. Make voice contact on CH16 and lend assistance if needed. DISTRESS ID123456789 PIRACY 12:45PM LOC Base Unit, Microphone and Handset Position and time data and the vessel's MMSID are shown on the LCD, and the data is recorded in the DISTRESS CALL LOG. Receiving a Distress Relay from another vessel An alarm sounds. Maintain a listening watch on CH16 and standby to lend assistance. Receiving a Distress Acknowledgement from a coast station An alarm sounds. Maintain a listening watch on CH16 and standby to lend assistance. For further information on these and other options, including radio setup and DSC options, troubleshooting, and channel charts, refer to the Navman VHF 7100 Owner's Manual. 13 NAVMAN VHF 7110 Quick Start Guide Navman VHF 7110 Installation Supplement This Installation Supplement is designed to be read with the Navman VHF RADIO INSTALLATION SHEET for 7000, 7100US, 7200US, 7100EU, 7200EU. It provides additional information that is specific to your VHF 7110 radio. Length = 10m Wall External Speaker Fuse Red Black GPS Navigation Receiver Water Proof Deck Outlet 14 NAVMAN VHF 7110 Installation Supplement Checklist - The following extra items are supplied in the VHF 7110 box: 1 2 3 4 5 6 7 8 · · · · · · 10m connection cable Rubber cushion Handset wallplate Two screws Protective cap Hexagonal nut Locking nut Handset cable 3 4 7 6 2 1 Also supplied, but not shown: Two self-tapping screws Two flat screws Two plain washers Two spring washers Two nuts Handset bulkhead mount 8 5 Handset and Microphone Bulkhead mount Handset Wallplate 20. 0 20. 0 40. 0 50. 0 Drill 2 x screw pilot holes Drill 1 x 25. 4mm (1") 38. 0 Installation Before doing any cutting or drilling, check that: · · · The intended location for the handset wallplate has reasonable access at the rear so that the 10m connection cable can be easily installed and accessed. The 10m connection cable comfortably reaches from the base unit to the intended location for the handset wallplate. The intended route for the 10m connection cable allows it to be secured to a bulkhead (or similar) along its length. 1. [. . . ] A-98, Sector 21, Noida - 201 301, India. Ph: +91 120 244 2697 TeleFax: +91 120 253 7881 Mobile: +91 98115 04557 e-mail: vkapil@del3. vsnl. net. in Esmario Export Enterprises Block No. F-1, 3rd Floor, Surya Towers Sardar Patel Rd, Secunderbad 500 003. Ph: +91 40 2784 5163 Fax: +91 40 2784 0595 e-mail: gjfeee@hd1. vsnl. net. in web: www. esmario. com Korea Kumhomarine Technology Co. [. . . ]